mirror of
https://github.com/pikvm/pikvm
synced 2024-11-05 00:00:28 +00:00
74e6262431
Fixed bubble for the reboot command Took out the ".r's" from usb0 line, looked like an error
56 lines
3.4 KiB
Markdown
56 lines
3.4 KiB
Markdown
# Ethernet-over-USB network
|
|
|
|
Specifically to v2. When combined with configuring a DNS server, FTP, or SMB (for example), this is a powerful way to extend the capabilities of Pi-KVM.
|
|
|
|
:exclamation: The USB-Ethernet features are experimental, so some of the default settings may be changed in future releases.
|
|
|
|
1. Edit `/etc/kvmd/override.yaml` (remove `{}` if this your first configuration entry) and add these lines:
|
|
``` yaml
|
|
otg:
|
|
devices:
|
|
ethernet:
|
|
enabled: true
|
|
driver: ecm
|
|
host_mac: 48:6f:73:74:50:43
|
|
kvm_mac: 42:61:64:55:53:42
|
|
```
|
|
The `host_mac` address will be used on the server's network interface. The `kvm_mac` means the address that will be assigned to the local interface on the Pi-KVM. The KVM interface will be called `usb0`network interface. If the `host_mac` or `kvm_mac` is not specified, a random value will be used. The `driver` parameter means the protocol that will be used for the USB network. The default value is `ecm` so it can be passed it this example. Other possible values are `eem`, `ncm` and `rndis`.
|
|
2. To automatically configure the USB network on the server recommended using the service `kvmd-otgnet`. It configures the firewall, assigns an address to the local Pi-KVM interface `usb0` and starts DHCP so the managed server can get the IPv4 address. By default, the address `169.254.0.1/28` to interface `usb0` will be assigned. One of the other addresses from the network `169.254.0.0./28` will be assigned to the server when it requests it via DHCP. For security reasons, all incoming connections from the server to the Pi-KVM side are blocked (except for ICMP and UDP port 67 which is used for DHCP). If you want to allow access from the server to the Pi-KVM interface, then you need to add ports 80 and 443 to the whitelist using `/etc/kvmd/override.yaml` file like this:
|
|
```yaml
|
|
otgnet:
|
|
firewall:
|
|
allow_tcp: [80, 443]
|
|
```
|
|
To view other available configuration parameters, use the command `kvmd -m`.
|
|
3. To enable the service, use the command `systemctl enable kvmd-otgnet`.
|
|
4. Perform `reboot`.
|
|
|
|
## Routing via Pi-KVM
|
|
|
|
By default, `kvmd-otgnet` will configure network connection between Pi-KVM and the server host only. The server host will not be able to reach other hosts beyond Pi-KVM. If the full network access is required from the server host through the USB-Ethernet feature (access all hosts Pi-KVM can access), additional settings are needed in `/etc/kvmd/override.yaml`.
|
|
|
|
1. Run `echo "net.ipv4.ip_forward = 1" > /etc/sysctl.d/99-kvmd-extra.conf`.
|
|
2. Add network interface to forward requests to (default gateway) by adding a line `forward_iface: <interface name>` under `firewall:`. Typically it would be `eth0` if the built-in ethernet port is used::
|
|
```yaml
|
|
otgnet:
|
|
firewall:
|
|
forward_iface: eth0
|
|
```
|
|
3. Add DNS server to provide host name resolution service. For example, adding `8.8.8.8` as DNS server requires addition of `dnsmasq` dhcp options. This can be done by adding following lines to `/etc/kvmd/override.yaml`:
|
|
```yaml
|
|
otgnet:
|
|
commands:
|
|
post_start_cmd_append:
|
|
- "--dhcp-option=6,8.8.8.8"
|
|
```
|
|
4. Combining above two together::
|
|
```yaml
|
|
otgnet:
|
|
firewall:
|
|
forward_iface: eth0
|
|
commands:
|
|
post_start_cmd_append:
|
|
- "--dhcp-option=6,8.8.8.8"
|
|
```
|
|
5. Don't forget ```reboot```.
|