mirror of
https://github.com/pikvm/pikvm
synced 2024-11-06 21:20:32 +00:00
174 lines
6.8 KiB
Markdown
174 lines
6.8 KiB
Markdown
# Raspberry Pi Pico HID
|
|
|
|
!!! warning "This page is under construction"
|
|
|
|
The Pico HID is a part of DIY PiKVM V1 platform and performs keyboard and mouse emulation.
|
|
It has excellent compatibility, and by default emulates USB, including two mouse modes: absolute and relative.
|
|
|
|
The scope of the Pico HID is not limited to V1 platform, it can also be used with V2 and even V3 platform
|
|
if you need to emulate a PS/2 keyboard and mouse or use [legacy multiport KVM switch](https://github.com/pikvm/pikvm/issues/7)
|
|
which does not fully support USB standards.
|
|
|
|
This page explains how to build, connect and use all the features of the Pico HID.
|
|
|
|
|
|
-----
|
|
## Making the Pico HID
|
|
|
|
If you are building the PiKVM V1, then all the necessary components should already be at your fingertips.
|
|
If you are making the Pico HID for V2 or V3, then here is what you will need:
|
|
|
|
* Raspberry Pi Pico board with soldered pins. [An official green board](https://pico.pinout.xyz) is recommended.
|
|
* *x1* USB-A to Micro-USB cable.
|
|
* *x10* dupont wires female-female.
|
|
* Optional: *x1* 1N5819 diode. But any similar one will do.
|
|
|
|
!!! tip "Tip for soldering guru"
|
|
If you know how to solder, you can buy the Pico without pins and no dupond wires, and just solder everything.
|
|
|
|
!!! warning
|
|
The diode is needed to provide the power to the Pico HID regardless of the host state,
|
|
and prevents backpowering problem. It will allow you to keep the keyboard buttons pressed
|
|
during the host power cycle, which is important for MacOS to get into the boot menus, for example.
|
|
|
|
Do not connect the red wire (the `VSYS (Pico) -> 5V (Pi)` line) without a diode.
|
|
If you can't find the diode, don't connect this wire at all.
|
|
|
|
Connect all the parts according to the scheme:
|
|
|
|
??? example "Simple wiring diagram"
|
|
<img src="basic_breadboard.png" />
|
|
|
|
??? example "Electrical schematic diagram for advanced users"
|
|
<img src="basic_scheme.png" />
|
|
|
|
|
|
-----
|
|
## Configuring the HID modes
|
|
|
|
By default, Pico HID emulates a USB keyboard and an absolute or relative mouse
|
|
(read [here](mouse.md) about the difference between mouse modes).
|
|
For most cases, nothing needs to be changed here. However, if you need something special
|
|
(like Windows 98 support), you can do it without reflashing on the current firmware.
|
|
|
|
To achieve this, the Pico HID uses a runtime configuration, which is set by connecting
|
|
some GPIOs with Ground (`GND`) lines.
|
|
|
|
| Pin name on the Pico board | Description |
|
|
|----------|-------------|
|
|
| `GP2` | Enable PS/2 keyboard & mouse support (see below). |
|
|
| `GP3` | Prefer the PS/2 keyboard over USB when turning on the HID (if PS/2 enabled). |
|
|
| `GP4` | Prefer the PS/2 mouse over USB (if PS/2 enabled) |
|
|
| `GP6` | Disable USB keyboard & mouse support. This is useful if you only want to use PS/2. |
|
|
| `GP7` | Enable the special USB absolute mouse for Windows 98. |
|
|
| `GP8` | Prefer the relative USB mouse over the absolute one. |
|
|
| `GP9` | Prefer the Windows 98 USB absolute mouse over the regular absolute one (if enabled). |
|
|
|
|
!!! example
|
|
To enable Windows 98 absolute mouse, just connect pin `GP9` to any `GND` [on the Pico](https://pico.pinout.xyz).
|
|
|
|
!!! warning
|
|
PS/2 is not implemented now. Soon (r) (c) (tm)
|
|
|
|
|
|
-----
|
|
## Flashing the firmware
|
|
|
|
To upload the firmware to Pico HID, you can use any computer with a USB port.
|
|
|
|
1. [Download](https://github.com/pikvm/kvmd/releases) the latest release of the firmware. The file is called `pico-hid.uf2`.
|
|
2. Press the white button on the Pico board and plug it using USB cable to the computer.
|
|
3. Release the button.
|
|
4. The Pico board appears as a flash drive on the host computer.
|
|
5. Copy the `pico-hid.uf2` file to this flash drive.
|
|
6. Safely disconnect the USB device.
|
|
|
|
|
|
-----
|
|
## The final steps
|
|
|
|
Connect the Pico HID to the host computer using the USB cable.
|
|
|
|
If you are building PiKVM V1, then no further action with the Pico HID is required.
|
|
|
|
If you are making the Pico HID for V2 or V3, add the following lines to the PiKVM configuration and reboot it.
|
|
|
|
!!! note "KVMD >= 3.241 is required for the Pico HID"
|
|
|
|
* `/boot/config.txt`
|
|
```ini
|
|
dtoverlay=spi0-1cs
|
|
```
|
|
|
|
* `/etc/kvmd/override.yaml`:
|
|
```yaml
|
|
kvmd:
|
|
hid:
|
|
type: spi
|
|
chip: 0
|
|
bus: 0
|
|
sw_cs_pin: 7
|
|
sw_cs_per_byte: true
|
|
reset_pin: 25
|
|
reset_inverted: true
|
|
reset_self: true
|
|
power_detect_pin: 16
|
|
power_detect_pull_down: true
|
|
```
|
|
|
|
|
|
-----
|
|
## Replacing the legacy Arduino HID
|
|
|
|
!!! warning
|
|
**This section is intended for advanced users of the [legacy Arduino HID](arduino_hid.md).**
|
|
|
|
It may seem tempting, but **don't to use the Arduino HID for new PiKVM builds**
|
|
just because you have it at your fingertips. Connecting and flashing Arduino
|
|
is much more time consuming than Pico. In addition, different Arduino board works
|
|
with different voltages, may or may not have SPI (for the Pico, we use SPI to free up
|
|
the UART on Raspberry Pi for the console and other useful things), etc.
|
|
|
|
Using the Pico HID is the recommended fast and standard way in the PiKVM world.
|
|
|
|
The Pico HID can be used to replace the [legacy Arduino HID](arduino_hid.md).
|
|
Moreover, it can use both Serial (UART) port and SPI. The connection scheme is also noticeably simplified,
|
|
getting rid of the transistor for the Reset line and level shifter for RX/TX (MOSI/MISO).
|
|
|
|
??? example "For the Arduino HID over SPI"
|
|
Throw away the Reset transistor and level shifter, and follow this guide
|
|
from the very beginning, as if you were connecting Pico HID for V2/V3.
|
|
|
|
??? example "For the classic Serial (UART) HID"
|
|
Get rid of the transistor and level shifter, and follow this guide
|
|
from the very beginning, but the schemes and configs will be slightly different.
|
|
|
|
* The `GP22` on the Pico is connected directly to the `GND`. This enables UART mode instead of default SPI.
|
|
|
|
* In the original V0, `GPIO4` [on the Raspberry Pi](https://pinout.xyz) was used for the Reset line.
|
|
Now we recommend to use `GPIO25` for consistency reasons.
|
|
However, you can use `GPIO4` by changing the `reset_pin` value in the config example below.
|
|
On the scheme, this is a yellow wire, the `RUN (Pico) -> GPIO25 (Pi)` line.
|
|
|
|
??? example "Simple wiring diagram"
|
|
<img src="serial_breadboard.png" />
|
|
|
|
??? example "Electrical schematic diagram"
|
|
<img src="serial_scheme.png" />
|
|
|
|
??? example "Configs"
|
|
* Don't add line `dtoverlay=spi0-1cs` to the `/boot/config.txt` file. It's only needed for SPI.
|
|
|
|
* `/etc/kvmd/override.yaml`:
|
|
```yaml
|
|
kvmd:
|
|
hid:
|
|
type: serial
|
|
device: /dev/kvmd-hid
|
|
reset_pin: 25
|
|
reset_inverted: true
|
|
reset_self: true
|
|
power_detect_pin: 16
|
|
power_detect_pull_down: true
|
|
```
|