"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 10x10 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 7x7 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 5x5 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- biliniear bedleveling with a 5x5 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F4 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 10x10 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F1 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 7x7 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F1 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 5x5 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F1 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- biliniear bedleveling with a 5x5 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 10x10 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 7x7 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 5x5 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- biliniear bedleveling with a 5x5 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F4 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 10x10 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F1 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 7x7 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F1 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 5x5 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F1 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- biliniear bedleveling with a 5x5 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 10x10 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 7x7 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 5x5 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- biliniear bedleveling with a 5x5 mesh
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed octorprint print progress
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality enabled
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F4 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 10x10 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F4 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 7x7 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F4 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- unified bedleveling with a 5x5 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
"folders and subfolders release"
Hi all,
as there is a firmware out for Ender 3 S1 Plus out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Plus with F4 chip.
My firmware does:
- Ender 3 S1 Plus only
- correct bed size (310x315)
- printing height 300 as stock firmware
- x-max position 310 to respect the cable
- y-max position 315 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.05
- Input Shaping activated and set to x 40hz and y 50hz.
- increased buffers for faster octorprint and sd communication
- increased feedrates in reasonable borders for faster printing
- increased min_segmenttime for better quality
- babystepping while printing fixed
- biliniear bedleveling with a 5x5 mesh
- probing margin bumped to 50mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=310 to y=315 to x=155 to y=157.5
- fixed filament runount sensor resume not functional
- fixed sd print pause resume not functional
- fixed Marlin Bug Linear Advance #25445
- fixed Marlin Bug Linear Advance #25442
- laser functionality
- included relevant Marlin Upstream fixes 02.2023 - 14.03.2023
- firmware supports now folders and subfolder - max 8 chars for a folder name, if longer it will not be entered
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 300mmx300mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Hope you like it.
