|
|
@ -8,15 +8,15 @@ Instructions:
|
|
|
|
Please do the following two tests:
|
|
|
|
Please do the following two tests:
|
|
|
|
|
|
|
|
|
|
|
|
1.)
|
|
|
|
1.)
|
|
|
|
- best is to start with leveled bed
|
|
|
|
- best is to start with a leveled bed
|
|
|
|
- flash the firmware
|
|
|
|
- flash the firmware
|
|
|
|
- reset to defaults via screen
|
|
|
|
- reset to defaults via screen
|
|
|
|
- heat up nozzle end bed to your desired temerature
|
|
|
|
- heat up nozzle and bed to your desired temerature
|
|
|
|
- g28
|
|
|
|
- g28
|
|
|
|
- got to leveling on the screen
|
|
|
|
- got to leveling on the screen
|
|
|
|
- got to point 2
|
|
|
|
- got to point 2
|
|
|
|
- set initial z-offset on this point that it has a around 2mm clearance (this is not final leveling
|
|
|
|
- set initial z-offset on this point that it has a around 2mm clearance (this is not final leveling
|
|
|
|
- go to points 3,4,5 an check if it nozzle to bed matches point 2, turn the wheels under bed to patch thos 2 mm..
|
|
|
|
- go to points 3,4,5 an check if it nozzle to bed matches point 2, turn the wheels under bed to patch those 2 mm..
|
|
|
|
- go back to point 2, lower your z-offset to your desired height via screen (paper method, gauge, etc)
|
|
|
|
- go back to point 2, lower your z-offset to your desired height via screen (paper method, gauge, etc)
|
|
|
|
- go to points 3,4,5 and adjust those with the wheels to match point 2
|
|
|
|
- go to points 3,4,5 and adjust those with the wheels to match point 2
|
|
|
|
- go around 2-3 times
|
|
|
|
- go around 2-3 times
|
|
|
@ -26,10 +26,10 @@ Please do the following two tests:
|
|
|
|
- watch your g-code for the x position of your purge lines. your bad now starts exactly at x=0 and y=0
|
|
|
|
- watch your g-code for the x position of your purge lines. your bad now starts exactly at x=0 and y=0
|
|
|
|
|
|
|
|
|
|
|
|
2.)
|
|
|
|
2.)
|
|
|
|
- best is to start with leveled bed
|
|
|
|
- best is to start with a leveled bed
|
|
|
|
- flash the firmware
|
|
|
|
- flash the firmware
|
|
|
|
- reset to defaults via screen
|
|
|
|
- reset to defaults via screen
|
|
|
|
- heat up nozzle end bed to your desired temerature
|
|
|
|
- heat up nozzle and bed to your desired temerature
|
|
|
|
- g28
|
|
|
|
- g28
|
|
|
|
- got to leveling on the screen
|
|
|
|
- got to leveling on the screen
|
|
|
|
- got to point 1
|
|
|
|
- got to point 1
|
|
|
|