pikvm/pages/ezcoo.md

# ezCoo managed multiport KVM switch

The ezCoo managed switch can be controlled by Pi-KVM to allow it to connect to multiple hosts. A typical scenario is a single Pi-KVM device which can control and switch between multiple hosts or servers using the ezCoo switch. UI elements can be added to the [GPIO dropdown](gpio.md) to allow switching between hosts from the Pi-KVM webpage. The instructions here were tested with the ~~[ezCoo SW41HA HDMI 4x1 switch](https://www.easycoolav.com/products/hdmi20-switch-4x1-with-usb20-kvm-4-port-usbsupport-4k60hz-444-and-hdr-audio-breakout)~~ [ezCoo EZ-SW41HA-KVMU3L 4x1 switch](https://www.easycoolav.com/products/hdmi20-switch-4x1-with-usb30-kvm-3-port-usbsupport-4k60hz-444-and-hdr-audio-breakout-36). Both older USB2.0 and newer USB3.0 variants are supported. The following was testing on a Raspberry Pi 4 but should also work on the Pi 2 and 3. This document was createdy using the contributions from multiple users on the [Pi-KVM Discord](https://discord.gg/bpmXfz5) and the author appreciates their efforts.

:exclamation: While most images of the switch do not show the sides, there is a Micro USB port on the side of the ezCoo switch. This is the management port, which is controlled via COM port on the ezCoo KVM.  When plugged into the Raspberry Pi, it appears as `/dev/ttyUSB0`.

:exclamation: Audio was not tested, it is assumed to be non-functional.

## Connections
From a high level, the ezCoo switch uses standard connections to the host machines (USB-A to USB-B and HDMI). The Raspberry Pi OTG connector (the one coming from the USB-C port on a Pi 4 via the custom splitter cable or device) should be connected to the USB 3 port on the ezCoo switch. There is an additional USB cable connected to the managed port on the switch.

1. Connect the USB-A cable from the Raspberry Pi OTG port to ezCoo switch USB 3 port on the front of the switch. **Note**: If this cable is connected to the keyboard port of the ezCoo switch the mouse will not be present.
2. Connect the HDMI out from the ezCoo switch to the Raspberry Pi CSI-2 to HMDI input. Other users have reported HMDI encoder USB dongles as working.
3. Connect a USB-A to Micro USB cable from the Raspberry Pi to the management port on the side of the ezCoo switch.
4. Connect host USB and HDMI cables from the ezCoo switch to the machines to be managed per the switch instructions.
5. At this point the KVM switch should be present as a device on the Pi-KVM. SSH into Pi-KVM and ensure a device like `/dev/ttyUSB0` is present. The following instructions assume this is the KVM switch.

:exclamation: There is a limitation in the underlying Pi-KVM software related to plugging video cables from a host which is already powered and connected to a monitor to a Raspberry Pi CSI2-HDMI encoder. These limitations apply equally when using the ezCoo KVM switch. If video is not present in Pi-KVM, try keeping all host machines off and connecting them directly to the ezCoo switch before powering the hosts on.

## Adding UI elements to control the KVM switch
The UI can be updated to add buttons to switch between KVM inputs and indicators for which input is currently selected.  The instructions below will make these available in the Pi-KVM UI after clicking the "GPIO" menu button in the KVM view.

1. SSH into Pi-KVM
2. Enable read-write mode on the sd card via `rw`
3. Edit the `/etc/kvmd/override.yaml` file and include the following. Note the assumption that the KVM switch is present on `/dev/ttyUSB0`:
```yaml
kvmd:
    gpio:
        drivers:
            ez:
                type: ezcoo
                device: /dev/ttyUSB0
        scheme:
            ch0_led:
                driver: ez
                pin: 0
                mode: input
            ch1_led:
                driver: ez
                pin: 1
                mode: input
            ch2_led:
                driver: ez
                pin: 2
                mode: input
            ch3_led:
                driver: ez
                pin: 3
                mode: input
            ch0_button:
                driver: ez
                pin: 0
                mode: output
                switch: false
            ch1_button:
                driver: ez
                pin: 1
                mode: output
                switch: false
            ch2_button:
                driver: ez
                pin: 2
                mode: output
                switch: false
            ch3_button:
                driver: ez
                pin: 3
                mode: output
                switch: false
        view:
            table:
                - ["#Input 1", ch0_led, ch0_button]
                - ["#Input 2", ch1_led, ch1_button]
                - ["#Input 3", ch2_led, ch2_button]
                - ["#Input 4", ch3_led, ch3_button]
  ```
4. Return to read-only mode for the sd card via `ro`
5. Restart the kvmd service: `systemctl restart kvmd`
6. If you are still not getting KB output, issue a ```ls -la /dev/tty* | grep USB``` , if no output change cables (Alot of cables are power only)

## Switching between hosts in the UI

To switch between hosts, enter the KVM UI and click the "GPIO" menu.  You should see 4 inputs, one of which will have a green circle indicating it is currently selected.  Click the other inputs to change the selected host.

## Additional step for the USB3.0 version

Please add ```protocol: 2``` to the override.yaml under the ```type: ezcoo``` at the same level:

```yaml
kvmd:
    gpio:
        drivers:
            ez:
                type: ezcoo
                protocol: 2
                device: /dev/ttyUSB0
 ```