mirror of
https://github.com/opnsense/docs
synced 2024-11-15 06:12:58 +00:00
75 lines
4.7 KiB
ReStructuredText
75 lines
4.7 KiB
ReStructuredText
====================================
|
|
Network
|
|
====================================
|
|
|
|
|
|
---------------------------------
|
|
Netmap (IPS, Sensei, ...)
|
|
---------------------------------
|
|
|
|
**General**
|
|
|
|
Netmap is a technology which enables fast packet processing while minimizing overhead, there are however some pitfalls
|
|
which may turn your network interface unreachable.
|
|
|
|
Before using this technology, always make sure you have access via another interface (or console) to your firewall
|
|
in case connectivity is dropped.
|
|
|
|
In order for netmap to function properly it is imperative that all sorts of driver / hardware acceleration is disabled
|
|
(:menuselection:`Interfaces -> Settings`), this include :code:`VLAN Hardware Filtering` as well (which wasn't disabled pre 20.7).
|
|
|
|
Some drivers have may have additional tunables, which enable hardware acceleration, make sure to disable them as well
|
|
(.e.g intel ixl has :code:`hw.ixl.enable_head_writeback`, which we disable by default)
|
|
|
|
Below you will find a list of tunables which are know to be (partial) incompatible with netmap.
|
|
|
|
=========================================== =================================================================================
|
|
Tunable Description
|
|
=========================================== =================================================================================
|
|
hw.ixl.enable_head_writeback Intel :code:`ixl(4)` tunable for increased tx performance,
|
|
OPNsense standard value is disabled.
|
|
dev.ax.<interface number>.sph_enable AMD tunable to split header and payload into a separate buffer respectively,
|
|
Netmap requires a uniform view of a packet. Disabled by default
|
|
on OPNsense.
|
|
=========================================== =================================================================================
|
|
|
|
**Decoupling Netmap from an application**
|
|
|
|
It can be useful to split the functionality of Netmap and the application using it in order to determine whether it's
|
|
Netmap or the application at fault for connectivity issues. To aid in this, Netmap's :code:`bridge` utility has been
|
|
added to our pkg repository for easy installation and use. To avoid ambiguity, it has been renamed to :code:`netmap-bridge`.
|
|
|
|
You can install it by running :code:`pkg install netmap-bridge` (:code:`man netmap-bridge`).
|
|
|
|
:code:`netmap-bridge` provides a L2 software bridge between two interfaces, but can also be used to bridge an interface
|
|
and the host network stack like Suricata does. To replicate the behaviour of Suricata without actually running Suricata, run
|
|
:code:`netmap-bridge -i netmap:igb1`. Replace the interface as appropriate. While it is running, pass traffic as normal to
|
|
determine if an original issue persists.
|
|
|
|
.. _errno:
|
|
|
|
---------------------------------
|
|
Common error codes
|
|
---------------------------------
|
|
|
|
Any piece of software that uses system calls to communicate over sockets use the standard interface
|
|
`errno.h <https://github.com/opnsense/src/blob/master/sys/sys/errno.h>`__ (:code:`man errno`). If an error
|
|
is logged, a return code is associated to a specific reason of failure. Some common ones are explained below:
|
|
|
|
====== ==================== =================================================================================
|
|
XX Name Description
|
|
====== ==================== =================================================================================
|
|
55 ENOBUFS No buffer space available. An operation on a socket or pipe was not performed
|
|
because the system lacked sufficient buffer space or because a queue was full.
|
|
**Check connectivity from the machine itself using** :code:`ping`, most common
|
|
mistakes are misconfigured routes, interface issues (disconnected) and
|
|
policy based routing issues forcing traffic to the wrong target
|
|
(using :code:`reply-to`)
|
|
64 EHOSTDOWN Host is down. A socket operation failed because the destination host was down.
|
|
**Expecting an (layer 2) ARP response but none was returned, often misconfigured
|
|
subnets or hosts are actually not accessible over L2**
|
|
65 EHOSTUNREACH No route to host. A socket operation was attempted to an unreachable host
|
|
**The routing table is a good place to look**
|
|
(:menuselection:`System --> Routes --> Status`)
|
|
====== ==================== =================================================================================
|