mirror of
https://github.com/opnsense/docs
synced 2024-11-15 06:12:58 +00:00
155 lines
5.8 KiB
ReStructuredText
155 lines
5.8 KiB
ReStructuredText
=========
|
|
Routes
|
|
=========
|
|
|
|
Routing is one of the core features of your firewall, which is responsible for forwarding packets over the network
|
|
based on (predefined) paths.
|
|
|
|
Within the routing section of your firewall you can keep track of configured routes and define static routes
|
|
yourself to teach your firewall which path it should take when forwarding packets to a specific network.
|
|
|
|
|
|
|
|
.. blockdiag::
|
|
:desctable:
|
|
|
|
blockdiag {
|
|
client [shape="cisco.pc", label="[1]"];
|
|
OPNsense [shape="cisco.firewall", label=""];
|
|
internet [shape="cisco.cloud"];
|
|
private_net [shape="cisco.cloud", label=""];
|
|
private_net2 [shape="cisco.cloud", label="[2]"];
|
|
Gateway1 [shape="cisco.router", label=""];
|
|
Gateway2 [shape="cisco.router", label="[3]"];
|
|
client -> OPNsense;
|
|
OPNsense -> Gateway1 -> internet;
|
|
OPNsense -> Gateway2 -> private_net;
|
|
OPNsense -> Gateway2 -> private_net2;
|
|
|
|
group {
|
|
label = "Client";
|
|
color = none;
|
|
|
|
client;
|
|
}
|
|
|
|
group {
|
|
label = "OPNsense";
|
|
color = none;
|
|
|
|
OPNsense;
|
|
}
|
|
|
|
group {
|
|
label = "Gateways";
|
|
color = none;
|
|
|
|
Gateway1 ;
|
|
Gateway2 ;
|
|
}
|
|
|
|
group {
|
|
label = "Networks";
|
|
color = none;
|
|
|
|
internet;
|
|
private_net;
|
|
private_net2;
|
|
}
|
|
}
|
|
|
|
|
|
When a client sends a packet to the firewall for a network not directly attached to it, the firewall would
|
|
normally check its routing table to determine to which gateway (see :doc:`/manual/gateways`) it should be send.
|
|
|
|
|
|
.. Tip::
|
|
Use traceroute (:menuselection:`Interfaces --> Diagnostics --> Trace Route`) to verify which path traffic would
|
|
follow to reach its destination.
|
|
|
|
----------------------
|
|
Configuration
|
|
----------------------
|
|
|
|
This is where you can setup static routes, looking at the diagram in the previous chapter, here you would define how
|
|
:code:`[1]` would access :code:`[2]` using router :code:`[3]`.
|
|
|
|
The number of settings are obviously limited, we need to know the gateway and the target network.
|
|
|
|
===========================================================================================================
|
|
|
|
============================= =============================================================================
|
|
Disabled (temporary) disable this item
|
|
Network Address Destination network to reach
|
|
Gateway The gateway to use.
|
|
Description Optional description for this item
|
|
============================= =============================================================================
|
|
|
|
|
|
.. Note::
|
|
Some services are known to update the routing table themselves, in which case you shouldn't add static routes
|
|
manually (OpenVPN manages its own routes for example).
|
|
|
|
|
|
----------------------
|
|
Status
|
|
----------------------
|
|
|
|
|
|
The status page shows the current active content of the routing table.
|
|
|
|
===========================================================================================================
|
|
|
|
============================= =============================================================================
|
|
Proto Protocol (IPv4 or IPv6)
|
|
Destination Destination network
|
|
Gateway Where to send the packet for this destination network
|
|
Flags Routes have associated flags which influence operation of the protocols
|
|
when sending to destinations matched by the routes.
|
|
See the **Flags** table below for details.
|
|
Use Counts the number of packets sent via this route
|
|
MTU The MTU set for this route
|
|
Netif Interface to use for this route
|
|
Netif (name) Name of the interface if found
|
|
Expire The time at which this route should expire, or zero if it should never expire.
|
|
It is the responsibility of individual protocol suites to ensure that routes are
|
|
actually deleted once they expire.
|
|
============================= =============================================================================
|
|
|
|
|
|
.............
|
|
Flags
|
|
.............
|
|
|
|
|
|
The following flags are supported by the kernel.
|
|
|
|
============================= =============================================================================
|
|
Letter / Flag Description
|
|
============================= =============================================================================
|
|
1 [RTF_PROTO1] Protocol specific routing flag
|
|
2 [RTF_PROTO2] Protocol specific routing flag
|
|
3 [RTF_PROTO3] Protocol specific routing flag
|
|
B [RTF_BLACKHOLE] Just discard pkts (during updates)
|
|
b [RTF_BROADCAST] The route represents a broadcast address
|
|
C [RTF_CLONING] Generate new routes on use
|
|
c [RTF_PRCLONING] Protocol-specified generate new routes on use
|
|
D [RTF_DYNAMIC] Created dynamically (by redirect)
|
|
d [RTF_DONE] Message confirmed
|
|
G [RTF_GATEWAY] Destination is a gateway
|
|
H [RTF_HOST] Host entry (net otherwise)
|
|
L [RTF_LLINFO] Valid protocol to link address translation
|
|
M [RTF_MODIFIED] Modified dynamically (by redirect)
|
|
R [RTF_REJECT] Host or net unreachable
|
|
S [RTF_STATIC] Manually added
|
|
U [RTF_UP] Route usable
|
|
X [RTF_XRESOLVE] External daemon resolves name
|
|
============================= =============================================================================
|
|
|
|
----------------------
|
|
Logs
|
|
----------------------
|
|
|
|
Route related logging, like :code:`radvd` and :code:`rtsold` for IPv6 write messages to this logging section
|
|
which can be used for debugging purposes.
|