mirror of
https://github.com/opnsense/docs
synced 2024-11-17 03:25:33 +00:00
84 lines
4.9 KiB
ReStructuredText
84 lines
4.9 KiB
ReStructuredText
====
|
|
DHCP
|
|
====
|
|
|
|
DHCP is used to automatically provide clients with an IP address (instead of clients having to set one themselves).
|
|
DHCP is available for both IPv4 and IPv6 clients, referred to as DHCPv4 and DHCPv6, respectively.
|
|
|
|
-----------------
|
|
Settings overview
|
|
-----------------
|
|
|
|
DHCPv4 settings can be found at :menuselection:`Services --> DHCPv4`. DHCPv6 settings can be found at :menuselection:`Services --> DHCPv6`.
|
|
|
|
The DHCPv4 submenu further consists of:
|
|
|
|
* An entry per interface of general settings, like a toggle to enable/disable DHCPv4 for this interface, DHCP range, DNS servers…
|
|
* **Relay**: DHCP requests can be “forwarded” to a DHCP server on another interface. This is called relaying.
|
|
* **Leases**: Shows all IP addresses that are handed out to clients (can be filtered to only show active and static leases).
|
|
* **Log File**: Shows the log file of the DHCPv4 server.
|
|
|
|
The DHCPv6 submenu further consists of:
|
|
|
|
* **Relay**: DHCP requests can be “forwarded” to a DHCP server on another interface. This is called relaying.
|
|
* **Leases**: Shows all IP addresses that are handed out to clients (can be filtered to only show active and static leases).
|
|
|
|
------------
|
|
Using DHCPv4
|
|
------------
|
|
|
|
A typical DHCPv4 usage scenario is using it on your LAN with an IP range of 192.168.1.x, where x can be a number from 1
|
|
through 254. This means a subnet mask of 255.255.255.0. The range can also be written as 192.168.1.0/24. (The “1” in
|
|
the third group can also be another number, and there are also other ranges available for private use. These are
|
|
described in `RFC 1918 <https://tools.ietf.org/html/rfc1918#section-3>`_.)
|
|
|
|
The LAN IP of the OPNsense device that serves DHCP to the LAN should fall in the same DHCP IP range. Typically, it gets
|
|
the address ending in .1 (so 192.168.1.1 in this example).
|
|
|
|
To set the LAN IP, go to :menuselection:`Interfaces --> [LAN]`, set “IPv4 Configuration Type” to “Static”, and under
|
|
“Static IPv4 configuration”, set “IPv4 address” to ``192.168.1.1`` and the subnet dropdown to “24”. Then click Save.
|
|
|
|
To set the DHCP settings, go to :menuselection:`Services --> DHCPv4 --> [LAN]`. Under “Gateway”, put ``192.168.1.1``. Under range,
|
|
put ``192.168.1.100`` as the start address and ``192.168.1.200`` as the end address. Then click Save. After saving,
|
|
click the “Apply Settings” button.
|
|
|
|
-------------------------
|
|
Advanced settings
|
|
-------------------------
|
|
|
|
To configure options that are not available in the GUI one can add custom configuration files on the firewall itself.
|
|
Files can be added in :code:`/usr/local/etc/dhcpd.opnsense.d/` for IPv4 and :code:`/usr/local/etc/dhcpd6.opnsense.d/`
|
|
for IPv6, these should use as extension .conf (e.g. custom-options.conf). When more files are placed inside the directory,
|
|
all will be included in alphabetical order.
|
|
|
|
.. Warning::
|
|
It is the sole responsibility of the administrator which places a file in the extension directory to ensure that the configuration is
|
|
valid.
|
|
|
|
.. _dhcp-relaying:
|
|
|
|
-------------
|
|
DHCP relaying
|
|
-------------
|
|
|
|
DHCP relaying is the forwarding of DHCP requests received on one interface to the DHCP server on another. DHCP
|
|
relaying is available for both DHCPv4 and DHCPv6. The DHCPv4 settings can be found at
|
|
:menuselection:`Services --> DHCPv4 --> Relay`. The DHCPv6 settings can be found at
|
|
:menuselection:`Services --> DHCPv6 --> Relay`.
|
|
|
|
When setting up DHCP relaying (both DHCPv4 and DHCPv6 relaying have the same settings), the following options are
|
|
available:
|
|
|
|
+-----------------------+----------------------------------------------------------------------------------------------+
|
|
| Setting | Explanation |
|
|
+=======================+==============================================================================================+
|
|
| Enable | |
|
|
+-----------------------+----------------------------------------------------------------------------------------------+
|
|
| Interface(s) | Which interfaces to apply relaying to. Only interfaces with an IP can be selected. |
|
|
+-----------------------+----------------------------------------------------------------------------------------------+
|
|
| Append circuit ID and | If this is checked, the DHCP relay will append the circuit ID (interface number) and the |
|
|
| agent ID to requests | agent ID to the DHCP request. |
|
|
+-----------------------+----------------------------------------------------------------------------------------------+
|
|
| Destination servers | A comma separated list of IPs to which the requests should be forwarded. |
|
|
+-----------------------+----------------------------------------------------------------------------------------------+
|