mirror of
https://github.com/opnsense/docs
synced 2024-11-18 21:28:29 +00:00
92 lines
4.5 KiB
ReStructuredText
92 lines
4.5 KiB
ReStructuredText
============================
|
|
WireGuard Road Warrior Setup
|
|
============================
|
|
|
|
------------
|
|
Introduction
|
|
------------
|
|
|
|
WireGuard is a simple, fast and modern VPN. It aims to be faster and simpler than IPSec. It intends to be
|
|
considerably more performant than OpenVPN. Initially released for the Linux kernel, it is now cross-platform
|
|
and widely deployable. It is currently under heavy development. We will describe here how to set up
|
|
WireGuard as a central server or just as a client.
|
|
|
|
---------------------
|
|
Step 1 - Installation
|
|
---------------------
|
|
|
|
Install the plugin as usual, refresh the page and you will find the client via :menuselection:`VPN --> WireGuard`.
|
|
|
|
--------------------------------
|
|
Step 2a - Setup WireGuard Server
|
|
--------------------------------
|
|
|
|
The setup of a central VPN server is very simple. Just go to tab **Local** and create a new instance.
|
|
Give it a **Name** and set a desired **Listen Port**. If you have more than one service instance be
|
|
aware that you can use the **Listen Port** only once. For **Tunnel Address** choose an unused network
|
|
to tunnel all clients just like with OpenVPN or GRE (e.g. 192.168.0.1/24).
|
|
**Peers** can not be chosen yet since we have not created them yet.
|
|
After hitting **Save changes** you can reopen the newly created instance, write down your new public
|
|
key and give it to the other side in a secure way (e.g. PGP encrypted or via SMS).
|
|
|
|
Now go to tab **Endpoints** and add the fist road warrior, give it a **Name**, insert the **Public
|
|
Key** and **Allowed IPs** e.g. *192.168.0.2/32, 10.10.10.0/24* (it is important to use /32 for the
|
|
tunnel address when using multiple endpoints). **Endpoint Address** and **Endpoint Port** can be left
|
|
empty since they are mostly dynamic, now hit **Save changes**.
|
|
|
|
Go back to tab **Local**, open the instance and choose the newly created endpoint in **Peers**.
|
|
|
|
Now we can **Enable** the VPN in tab **General** and continue with the setup.
|
|
|
|
If you want to add more users just add them in **Endpoints** and link them via **Peers**.
|
|
|
|
------------------------
|
|
Step 2b - Setup Firewall
|
|
------------------------
|
|
|
|
On :menuselection:`Firewall --> Rules` add a new rule on your WAN interface allowing the port you set in your
|
|
instance (Protocol UDP). You also have a new interace **Wireguard** in rules, where you can
|
|
set granular rules on connection inside your tunnel.
|
|
|
|
Your tunnel is now up and running.
|
|
|
|
---------------------------------
|
|
Step 2c - Assignments and Routing
|
|
---------------------------------
|
|
|
|
With this setup your clients can reach your internal networks when they add it vial **Allowed IPs**.
|
|
But what if you want to push all traffic via VPN in order to filter some streams out of it?
|
|
Then we have to assign the interface via :menuselection:`Interface --> Assignments`, choose our instance (e.g. instance
|
|
0 is interface wg0), enable it, hit **Prevent Interface Removal** and don't configure an IP address.
|
|
|
|
After this we can go to :menuselection:`Firewall --> NAT --> Outbound` and add a rule. Check that rule generation is set
|
|
to manual or hybrid. Add a rule and select your WAN as **Interface**. **Source** should be the Tunnel
|
|
Network you use and **Translation / target** set to WAN address.
|
|
|
|
Now when you add 0.0.0.0/0 on your road warrior, outgoing packets are translated and reach the
|
|
Internet via your VPN.
|
|
|
|
When assigning interfaces we can also add gateways to them. This would offer you the chance to
|
|
balance traffic via different VPN providers or do more complex routing scenarios.
|
|
To do this, go to :menuselection:`System --> Gateways --> Single` and add a new gateway. Choose your WireGuard interface
|
|
and set the Gateway to **dynamic**.
|
|
|
|
-------------------------------
|
|
Step 3 - Setup WireGuard Client
|
|
-------------------------------
|
|
|
|
The development of WireGuard is very dynamic so this howto won't include any screenshots since
|
|
features are added rapidly or naming might change.
|
|
If we have OPNsense also at the client side the configuration is similar to step 3a but you have to
|
|
choose **Allowed IPs** within the range of the server side and exchange public keys after
|
|
the creation of a new instance. Then networks which should be routed via WireGuard have to be
|
|
added to your **Allowed IPs** in the endpoint configuration of your client (e.g. 192.168.0.0/24
|
|
when this is the LAN of WireGuard server). For pushing all network traffic via VPN you can add
|
|
0.0.0.0/0. If you do this it's important to also specifiy a DNS server which will be added to your
|
|
interface. Therefore go to **Local**, edit your instance and fill in one or more IP addresses to
|
|
the **DNS** field.
|
|
|
|
|
|
|
|
That's it!
|