mirror of
https://github.com/opnsense/docs
synced 2024-11-18 21:28:29 +00:00
121 lines
7.4 KiB
ReStructuredText
121 lines
7.4 KiB
ReStructuredText
==============
|
|
Network Time
|
|
==============
|
|
|
|
OPNsense ships with a standard `NTPd <http://doc.ntp.org/current-stable/>`__ server,
|
|
which synchronizes time with upstream servers and provides time to connected clients.
|
|
|
|
A newly installed firewall comes with NTP enabled on all interfaces (firewall blocks all non LAN access in this case),
|
|
forwarding queries to one of the :code:`X.opnsense.pool.ntp.org` upstreams (:code:`X` is any of 0,1,2,3).
|
|
|
|
-------------------------
|
|
General settings
|
|
-------------------------
|
|
|
|
In most cases the default setup is ready to use, below you will find some of the general options which can be configured.
|
|
|
|
=====================================================================================================================
|
|
|
|
.. Attention::
|
|
|
|
NTPd syncs the local clock to remote NTP servers and listens for incoming client queries using the selected interfaces.
|
|
The interface selection must therefore include a WAN type interface so that normal routing to the internet can take place.
|
|
Only selecting a LAN type interface will likely work due to outbound NAT rules, however, if CARP is configured, it is
|
|
possible that such NAT rules will translate to the address of the CARP VIP, causing asymmetric routing for secondary nodes.
|
|
|
|
Unless you are sure that you want to use a specific interface, it is recommended to keep the default of listening
|
|
on all interfaces and use the firewall rules to constrain access to the NTP service.
|
|
See `Listen interfaces <settingsmenu.html#listen-interfaces>`__ for more information.
|
|
|
|
==================================== ===============================================================================
|
|
Interface(s) Interfaces to listen on. This interface selection is also used for outgoing
|
|
queries. when no interfaces are selected it listens on all interfaces with a
|
|
wildcard. Selecting all interfaces will explicitly listen on only the
|
|
interfaces/IPs specified. Interfaces without an IP address will not be shown.
|
|
Time servers Servers to use, comes with two toggles:
|
|
|
|
* Prefer
|
|
Marks the server as preferred.
|
|
* Do not use
|
|
Marks the server as unused, except for display purposes.
|
|
The server is discarded by the selection algorithm.
|
|
Orphan mode Orphan mode allows the system clock to be used when no other
|
|
clocks are available. The number here specifies the stratum reported
|
|
during orphan mode and should normally be set to a number high enough to
|
|
insure that any other servers available to clients are
|
|
preferred over this server.
|
|
NTP graphs Enable RRD graphs of NTP statistics, which can be viewed in
|
|
:menuselection:`Reporting --> Health`
|
|
Syslog logging Extend logging with peer and/or system messages
|
|
Statistics logging Enable statistical logging in :code:`/var/log/ntp`, doesn't come with a
|
|
user interface
|
|
Access restrictions Within the access restriction row, you can set various options which
|
|
limit the use of ntpd and in some cases instruct ntpd how to handle
|
|
rejected clients.
|
|
Leap seconds You can manually supply ntpd with a leap seconds file, more detailed info
|
|
on the contents of those files can be found
|
|
`here <http://support.ntp.org/bin/view/Support/ConfiguringNTP#Section_6.14.>`__
|
|
==================================== ===============================================================================
|
|
|
|
|
|
.. Note::
|
|
|
|
NTPs is disabled if no Time servers are configured. There is no separate enable/disable toggle.
|
|
|
|
|
|
-------------------------
|
|
GPS
|
|
-------------------------
|
|
|
|
If you own a gps receiver, which supports NMEA, you can use it as a reference clock and configure it in this section.
|
|
For some brands settings are preconfigured, you can also use custom settings.
|
|
|
|
|
|
-------------------------
|
|
PPS
|
|
-------------------------
|
|
|
|
If your GPS receiver supports PPS (Pulse Per Second) output or you have a separate PPS signal available, you
|
|
can configure the serial port to use along with some other settings here.
|
|
|
|
|
|
-------------------------
|
|
Status
|
|
-------------------------
|
|
|
|
The status page can be used to query the health of the upstream time sources, it shows the following characteristics.
|
|
|
|
|
|
========================================================================================================================
|
|
|
|
==================================== ==================================================================================
|
|
Status Human readable status of the upstream
|
|
Server Upstream source
|
|
Ref ID Source IP address or
|
|
`kiss code: <http://doc.ntp.org/4.2.6p5/decode.html#kiss>`__
|
|
Stratum NTP uses a hierarchical, semi-layered system of time sources
|
|
(`wikipedia <https://en.wikipedia.org/wiki/Network_Time_Protocol#Clock_strata>`__)
|
|
This field shows the stratum of the upstream source
|
|
(lower usually means closer to the actual time source)
|
|
Type Type of time source, one of:
|
|
|
|
* u: unicast or manycast client
|
|
* b: broadcast or multicast client
|
|
* p: pool source
|
|
* l: local (reference clock)
|
|
* s: symmetric (peer)
|
|
* A: manycast server
|
|
* B: broadcast server
|
|
* M: multicast server
|
|
When time in seconds, minutes, hours, or days since the last packet was
|
|
received, or '-' if a packet has never been received
|
|
Poll poll interval in seconds
|
|
Reach reach shift register (octal), when set to :code:`377` all 8 bits are set and thus
|
|
no responses have been lost. Convert to bits to inspect which tries failed.
|
|
(e.g. :code:`257` --> :code:`10101111` means the last four responses
|
|
where received and two where lost within the last 8 tries)
|
|
Delay roundtrip delay in milliseconds
|
|
Offset offset time in milliseconds of the server relative to this host
|
|
Jitter indicates the difference, in milliseconds, between two samples
|
|
==================================== ==================================================================================
|