mirror of
https://github.com/opnsense/docs
synced 2024-11-15 06:12:58 +00:00
54eef60c16
* Update wireguard-client.rst - Add MTU and MSS hints * Update wireguard-s2s.rst - Add MTU and MSS hints * Update wireguard-s2s.rst - changed mss values * Update wireguard-s2s.rst - Reworked How-To completely * Update wireguard-client.rst - adjusted mss value * Update wireguard-client.rst - Different mss values for IPv4 and IPv6 * Update wireguard-s2s.rst - Improved some aspects * Update wireguard-client.rst - Improved some aspects Normalization rules should have different MSS values for either IPv4, or IPv4+IPv6. Changed the protocol back to any, since I'm unsure if selecting TCP only means IPv4 TCP, since there is also only IPv6 selectable. * Update wireguard-s2s.rst - Omitted Source Port in Firewall rules - Added tip and note about dynamic WAN IP * Update wireguard-s2s.rst - Terminology changes 23.7.6 - Changed Local to Instance - Changed Endpoint to Peer - Added information about CARP vhid tracking to mitigate HA problems. - Added note about Keepalive for NATed sites.
287 lines
15 KiB
ReStructuredText
287 lines
15 KiB
ReStructuredText
============================
|
|
WireGuard Site-to-Site Setup
|
|
============================
|
|
|
|
------------
|
|
Introduction
|
|
------------
|
|
|
|
WireGuard is a simple and fast modern VPN protocol. It aims to be less complicated than IPSec, working more like ssh with private and public keys.
|
|
It has fewer lines of code and is more easily audited than other VPN protocols. Initially released for the Linux kernel, it is now cross-platform and widely deployable.
|
|
|
|
.. Attention::
|
|
Wireguard is useful for simple routed site to site tunnels and roadwarrior setups. To this date, it doesn't play too nicely with high availability setups. That's because the peer may keep polling a stale interface and misinterpret the other instance as being the one that is down and keep sending traffic there. Also, because Wireguard is bound to all interfaces (and not explicitely the CARP VIP), both High Availability firewalls will send handshakes and fight against each other for the remote Wireguard peer. This behavior was mitigated in 23.7.6 with Wireguard CARP vhid tracking that disables the Wireguard Instance with CARP VIPs in Backup state. In case of critical workloads and high availability, IPsec could still be the better choice.
|
|
|
|
.. Note::
|
|
The following example covers an IPv4 Site to Site Wireguard Tunnel between two OPNsense Firewalls with public IPv4 addresses on their WAN interfaces. You will connect *Site A LAN Net* ``172.16.0.0/24`` to *Site B LAN Net* ``192.168.0.0/24`` using the *Wireguard Transfer Net* ``10.2.2.0/24``. *Site A Public IP* is ``203.0.113.1`` and *Site B Public IP* is ``203.0.113.2``.
|
|
|
|
.. Tip::
|
|
You can also easily expand this Site to Site tunnel with IPv6 Global Unicast addresses (GUA) or Unique Local Addresses (ULA) to create a Dual Stack tunnel. Just add these IPv6 Networks (usually with /64 Prefix) to the *allowed IPs* and create Firewall rules to allow the traffic.
|
|
|
|
---------------------
|
|
Step 1 - Installation
|
|
---------------------
|
|
|
|
Install the os-wireguard plugin in :menuselection:`System --> Firmware --> Plugins`, refresh the GUI and you will soon find :menuselection:`VPN --> WireGuard`.
|
|
|
|
-----------------------------------------------------
|
|
Step 2a - Setup WireGuard Instance on OPNsense Site A
|
|
-----------------------------------------------------
|
|
|
|
Go to tab **Instances** and press **+** to create a new instance.
|
|
|
|
Enable the *advanced mode* toggle.
|
|
|
|
====================== ====================================================================================================
|
|
**Enabled** *Checked*
|
|
**Name** *wgopn-site-a*
|
|
**Public Key** *Generate with "Generate new keypair" button*
|
|
**Private Key** *Generates automatically*
|
|
**Listen Port** *51820*
|
|
**MTU** *1420 (default) or 1412 if you use PPPoE*
|
|
**Tunnel Address** *10.2.2.1/24*
|
|
**Peers** *Populated in later step*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
-----------------------------------------------------
|
|
Step 2b - Setup WireGuard Instance on OPNsense Site B
|
|
-----------------------------------------------------
|
|
|
|
Go to tab **Instance** and press **+** to create a new instance.
|
|
|
|
Enable the *advanced mode* toggle.
|
|
|
|
====================== ====================================================================================================
|
|
**Enabled** *Checked*
|
|
**Name** *wgopn-site-b*
|
|
**Public Key** *Generate with "Generate new keypair" button*
|
|
**Private Key** *Generates automatically*
|
|
**Listen Port** *51820*
|
|
**MTU** *1420 (default) or 1412 if you use PPPoE*
|
|
**Tunnel Address** *10.2.2.2/24*
|
|
**Peers** *Populated in later step*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
------------------------------------------------------
|
|
Step 3a - Setup WireGuard Peer on OPNsense Site A
|
|
------------------------------------------------------
|
|
|
|
Go to tab **Peers** and press **+** to create a new peer.
|
|
|
|
Enable the *advanced mode* toggle.
|
|
|
|
====================== ====================================================================================================
|
|
**Enabled** *Checked*
|
|
**Name** *wgopn-site-b*
|
|
**Public Key** *Insert the public key of the instance from wgopn-site-b*
|
|
**Shared Secret** *Leave empty*
|
|
**Allowed IPs** *10.2.2.2/32 192.168.0.0/24*
|
|
**Endpoint Address** *203.0.113.2*
|
|
**Endpoint Port** *51820*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
Go to tab **Instances** and edit *wgopn-site-a*.
|
|
|
|
====================== ====================================================================================================
|
|
**Peers** *wgopn-site-b*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
------------------------------------------------------
|
|
Step 3b - Setup WireGuard Peer on OPNsense Site B
|
|
------------------------------------------------------
|
|
|
|
Go to tab **Peers** and press **+** to create a new peer.
|
|
|
|
Enable the *advanced mode* toggle.
|
|
|
|
====================== ====================================================================================================
|
|
**Enabled** *Checked*
|
|
**Name** *wgopn-site-a*
|
|
**Public Key** *Insert the public key of the instance instance from wgopn-site-a*
|
|
**Shared Secret** *Leave empty*
|
|
**Allowed IPs** *10.2.2.1/32 172.16.0.0/24*
|
|
**Endpoint Address** *203.0.113.1*
|
|
**Endpoint Port** *51820*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
Go to tab **Instances** and edit *wgopn-site-b*.
|
|
|
|
====================== ====================================================================================================
|
|
**Peers** *wgopn-site-a*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
.. Tip::
|
|
If one of your sites has a dynamic WAN IP address, you can leave the *Endpoint Address* on the site with the static IP address empty. The site with the dynamic IP will then be the initiator, and the site with the static IP will be the responder. Adjust the Firewall rule accordingly to allow any Source IP to connect to the static site.
|
|
|
|
.. Note::
|
|
If you use hostnames in the *Endpoint Address*, Wireguard will only resolve them once when you start the tunnel. If both sites have dynamic *Endpoint Addresses* set, the tunnel will stop working when they both use DynDNS hostnames, and one (or both) sites receive a new WAN IP lease from the ISP. You could probably mitigate this with a cron job that restarts wireguard periodically.
|
|
|
|
.. Note::
|
|
If a site is behind NAT, a keepalive has to be set on the site behind the NAT. The keepalive should be 25 seconds as stated in the official wireguard docs. It keeps the UDP session open when no traffic flows, preventing the wireguard tunnel from becoming stale because the outbound port changes.
|
|
|
|
-------------------------------
|
|
Step 4a - Setup Firewall Site A
|
|
-------------------------------
|
|
|
|
Go to :menuselection:`Firewall --> Rules --> WAN` add a new rule to allow incoming wireguard traffic from Site B.
|
|
|
|
====================== ====================================================================================================
|
|
**Action** *Pass*
|
|
**Interface** *WAN*
|
|
**Direction** *In*
|
|
**TCP/IP Version** *IPv4*
|
|
**Protocol** *UDP*
|
|
**Source** *203.0.113.2*
|
|
**Destination** *203.0.113.1*
|
|
**Destination port** *51820*
|
|
**Description** *Allow Wireguard from Site B to Site A*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
Go to :menuselection:`Firewall --> Settings --> Normalization` and add a new rule to prevent fragmentation of traffic going through the wireguard tunnel.
|
|
|
|
============================ ==================================================================================================
|
|
**Interface** *WireGuard (Group)*
|
|
**Direction** *Any*
|
|
**Protocol** *any*
|
|
**Source** *any*
|
|
**Destination** *any*
|
|
**Destination port** *any*
|
|
**Description** *Wireguard MSS Clamping Site A*
|
|
**Max mss** *1380 or lower, subtract at least 40 bytes from the Wireguard MTU*
|
|
============================ ==================================================================================================
|
|
|
|
.. Note::
|
|
By creating the normalization rules, you ensure that IPv4 TCP can pass through the Wireguard tunnel without being fragmented. Otherwise you could get working ICMP and UDP, but some encrypted TCP sessions will refuse to work. If you want to use IPv6 TCP, lower the MSS by 60 bytes instead of 40 bytes.
|
|
|
|
-------------------------------
|
|
Step 4b - Setup Firewall Site B
|
|
-------------------------------
|
|
|
|
Go to :menuselection:`Firewall --> Rules --> WAN` add a new rule to allow incoming wireguard traffic from Site A.
|
|
|
|
====================== ====================================================================================================
|
|
**Action** *Pass*
|
|
**Interface** *WAN*
|
|
**Direction** *In*
|
|
**TCP/IP Version** *IPv4*
|
|
**Protocol** *UDP*
|
|
**Source** *203.0.113.1*
|
|
**Destination** *203.0.113.2*
|
|
**Destination port** *51820*
|
|
**Description** *Allow Wireguard from Site A to Site B*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
Go to :menuselection:`Firewall --> Settings --> Normalization` and add a new rule to prevent fragmentation of traffic going through the wireguard tunnel.
|
|
|
|
============================ ==================================================================================================
|
|
**Interface** *WireGuard (Group)*
|
|
**Direction** *Any*
|
|
**Protocol** *any*
|
|
**Source** *any*
|
|
**Destination** *any*
|
|
**Destination port** *any*
|
|
**Description** *Wireguard MSS Clamping Site B*
|
|
**Max mss** *1380 or lower, subtract at least 40 bytes from the Wireguard MTU*
|
|
============================ ==================================================================================================
|
|
|
|
-----------------------------------------------
|
|
Step 4c - Enable Wireguard on Site A and Site B
|
|
-----------------------------------------------
|
|
|
|
Go to :menuselection:`VPN --> WireGuard --> Settings` on both sites and **Enable WireGuard**
|
|
|
|
Press **Apply** and check :menuselection:`VPN --> WireGuard --> Diagnostics`. You should see *Send* and *Received* traffic and *Handshake* should be populated by a number. This happens as soon as the first traffic flows between the sites.
|
|
|
|
Your tunnel is now up and running.
|
|
|
|
----------------------------------------------------------------
|
|
Step 5 - Allow traffic between Site A LAN Net and Site B LAN Net
|
|
----------------------------------------------------------------
|
|
|
|
Go to OPNsense Site A :menuselection:`Firewall --> Rules --> LAN A` add a new rule.
|
|
|
|
====================== ====================================================================================================
|
|
**Action** *Pass*
|
|
**Interface** *LAN A*
|
|
**Direction** *In*
|
|
**TCP/IP Version** *IPv4*
|
|
**Protocol** *Any*
|
|
**Source** *172.16.0.0/24*
|
|
**Source port** *Any*
|
|
**Destination** *192.168.0.0/24*
|
|
**Destination port** *Any*
|
|
**Description** *Allow LAN Site A to LAN Site B*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
Go to OPNsense Site A :menuselection:`Firewall --> Rules --> Wireguard (Group)` add a new rule.
|
|
|
|
====================== ====================================================================================================
|
|
**Action** *Pass*
|
|
**Interface** *Wireguard (Group)*
|
|
**Direction** *In*
|
|
**TCP/IP Version** *IPv4*
|
|
**Protocol** *Any*
|
|
**Source** *192.168.0.0/24*
|
|
**Source port** *Any*
|
|
**Destination** *172.16.0.0/24*
|
|
**Destination port** *Any*
|
|
**Description** *Allow LAN Site B to LAN Site A*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**. Allowed IPs
|
|
|
|
Go to OPNsense Site B :menuselection:`Firewall --> Rules --> LAN A` add a new rule.
|
|
|
|
====================== ====================================================================================================
|
|
**Action** *Pass*
|
|
**Interface** *LAN B*
|
|
**Direction** *In*
|
|
**TCP/IP Version** *IPv4*
|
|
**Protocol** *Any*
|
|
**Source** *192.168.0.0/24*
|
|
**Source port** *Any*
|
|
**Destination** *172.16.0.0/24*
|
|
**Destination port** *Any*
|
|
**Description** *Allow LAN Site B to LAN Site A*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
Go to OPNsense Site B :menuselection:`Firewall --> Rules --> Wireguard (Group)` add a new rule.
|
|
|
|
====================== ====================================================================================================
|
|
**Action** *Pass*
|
|
**Interface** *Wireguard (Group)*
|
|
**Direction** *In*
|
|
**TCP/IP Version** *IPv4*
|
|
**Protocol** *Any*
|
|
**Source** *172.16.0.0/24*
|
|
**Source port** *Any*
|
|
**Destination** *192.168.0.0/24*
|
|
**Destination port** *Any*
|
|
**Description** *Allow LAN Site A to LAN Site B*
|
|
====================== ====================================================================================================
|
|
|
|
Press **Save** and **Apply**.
|
|
|
|
.. Note::
|
|
Now both sites have full access to the LAN of the other Site through the Wireguard Tunnel. For additional networks just add more **Allowed IPs** to the Wireguard Endpoints and adjust the firewall rules to allow the traffic.
|