mirror of
https://github.com/opnsense/docs
synced 2024-11-15 06:12:58 +00:00
90 lines
3.3 KiB
ReStructuredText
90 lines
3.3 KiB
ReStructuredText
**How to set up a LAN Bridge**
|
|
==============================
|
|
|
|
**Original Author:** Martin Wasley
|
|
|
|
**Introduction**
|
|
-----------------
|
|
LAN Bridges should really only be used where the LAN secondary, tertiary and other interfaces
|
|
are not heavily used, if that is the case then it is recommended that an external switch
|
|
be used instead. That being said, if the CPU is fast enough then it will easily cope with
|
|
the extra load placed upon it by the bridge.
|
|
|
|
When creating a LAN bridge it is essential that you have physical access to the device,
|
|
you will need to swap the LAN connection at a certain point.
|
|
|
|
**Step One**
|
|
-----------------
|
|
Configure OPNsense as normal, with a single LAN interface, make sure that it works correctly.
|
|
It's a good idea to add the extra NIC interfaces ( OPTx ) during installation.
|
|
|
|
**Step Two**
|
|
-----------------
|
|
Create the bridge itself. Select :menuselection:`Interfaces --> Other Types --> Bridge` and ADD a new bridge. Select
|
|
from the member interfaces the unused interfaces you wish to add to the bridge, OPT2,OPT3 etc.
|
|
|
|
.. image:: images/lan_bridge_1.png
|
|
:width: 100%
|
|
|
|
Now Save the new bridge.
|
|
|
|
.. Note::
|
|
It is imperative that the member interfaces have nothing set within them for IPv4 or IPv6,
|
|
each member interface should be enabled and they should look like this:
|
|
|
|
.. image:: images/lan_bridge_2.png
|
|
:width: 100%
|
|
|
|
**Step Three**
|
|
-----------------
|
|
Select :menuselection:`Interfaces --> Assignments` and for the LAN interface, select the bridge previously created
|
|
and Save.
|
|
|
|
.. image:: images/lan_bridge_3.png
|
|
:width: 100%
|
|
|
|
At this point you will need to swap your LAN cable from the existing LAN connection to one of
|
|
the NICs that were added to the bridge interface, once connected then you must wait, it can take some
|
|
time for the interface to come back up, but keep refreshing the web interface until it does.
|
|
|
|
**Step Four**
|
|
-----------------
|
|
The Original LAN interface is now unassigned and will need to be re-assigned. Go to
|
|
:menuselection:`Interfaces --> Assignments` and in the New Interface box you will see the NIC itself ( igb*, em* ),
|
|
select it and hit the '+' button to add an assignment, then click Save.
|
|
|
|
.. image:: images/lan_bridge_5.png
|
|
:width: 100%
|
|
|
|
**Step Five**
|
|
-----------------
|
|
Select :menuselection:`Interfaces --> Other Types --> Bridge` and add the interface created in Step Four to the bridge
|
|
and Save, remember to check the new interface and ensure it is enabled as in Step Two.
|
|
|
|
.. image:: images/lan_bridge_4.png
|
|
:width: 100%
|
|
|
|
**Step Six**
|
|
-----------------
|
|
We now need to make two changes to the System Tunables to ensure that filtering is carried
|
|
out on the bridge itself, and not on the member interfaces. Go to :menuselection:`System --> Settings --> Tunables`
|
|
and select using the pen button net.link.bridge.pfil_member and set the value to 0
|
|
(add a new record if this entry doesn't exist on your installation).
|
|
|
|
.. image:: images/lan_bridge_6.png
|
|
:width: 100%
|
|
|
|
Select the tunable net.link.bridge.pfil_bridge and set the value to 1
|
|
|
|
.. image:: images/lan_bridge_7.png
|
|
:width: 100%
|
|
|
|
**Final**
|
|
-----------------
|
|
Once complete, the :menuselection:`Interface --> Assignments` page should look similar to this:
|
|
|
|
.. image:: images/lan_bridge_8.png
|
|
:width: 100%
|
|
|
|
|
|
Now reboot, when the system restores you should have a fully functional bridge interface. |