mirror of
https://github.com/opnsense/docs
synced 2024-11-15 06:12:58 +00:00
309 lines
13 KiB
ReStructuredText
309 lines
13 KiB
ReStructuredText
|
||
==============
|
||
Configure CARP
|
||
==============
|
||
|
||
|
||
--------
|
||
Overview
|
||
--------
|
||
|
||
One of the more powerful features of OPNsense is to set-up a redundant
|
||
firewall with automatic fail-over option. This chapter describes step by
|
||
step how to create a set-up based on two networks. The 192.168.1.0/24
|
||
will be used for the internal network and 172.18.0.0/24 will be used to
|
||
route our traffic to the internet.
|
||
|
||
.. image:: ./images/900px-Carp_setup_example.png
|
||
:width: 100%
|
||
|
||
When using CARP ( `FreeBSD handbook on CARP <https://www.freebsd.org/doc/handbook/carp.html>`__ ), all
|
||
fail-safe interfaces should have a dedicated IP address which will be
|
||
combined with one shared virtual IP address to communicate to both
|
||
networks. In the picture above the dashed lines are used to mark the
|
||
virtual addresses.
|
||
|
||
The configuration file (XML) for both firewalls can be downloaded from
|
||
the wiki.
|
||
|
||
-----------
|
||
Terminology
|
||
-----------
|
||
|
||
There is some terminology involved in setting up a CARP cluster, which
|
||
we will explain briefly first:
|
||
|
||
.. rubric:: CARP
|
||
:name: carp
|
||
|
||
Common Address Redundancy Protocol uses IP protocol 112, is derived from
|
||
OpenBSD and uses multicast packets to signal its neighbours about its
|
||
status. Always make sure that each interface can receive CARP packets.
|
||
Every virtual interface must have a unique Virtual Host ID (vhid), which
|
||
is shared across the physical machines. To determine which physical
|
||
machine has a higher priority, the advertised skew is used. A lower skew
|
||
means a higher score. (our master firewall uses 0).
|
||
|
||
|
||
.. rubric:: pfSync
|
||
:name: pfsync
|
||
|
||
Together with CARP, we can use pfSync to replicate our firewalls state.
|
||
When failing over you need to make sure both machines know about all
|
||
connections to make the migration seamless. It's highly advisable to use
|
||
a dedicated interface for pfSync packets between the hosts, both for
|
||
security reasons (state injection) as for performance.
|
||
|
||
.. Warning::
|
||
When using different network drivers on both machines, like running a HA
|
||
setup with one physical machine as master and a virtual machine as slave,
|
||
states can not be synced as interface names differ. The only workaround
|
||
would be to set up a LAGG.
|
||
|
||
.. rubric:: XMLRPC sync
|
||
:name: xmlrpc-sync
|
||
|
||
OPNsense includes a mechanism to keep the configuration of the backup
|
||
server in sync with the master. This mechanism is called XMLRPC sync and
|
||
can be found under :menuselection:`System --> High Availability --> Settings`.
|
||
|
||
-----------------------------------------
|
||
Setup interfaces & basic firewall rules
|
||
-----------------------------------------
|
||
|
||
.. Warning::
|
||
Make sure the interface assignments on both systems are identical!
|
||
Via :menuselection:`Interfaces --> Overview` you can check if e.g. DMZ is opt1 on
|
||
both machines. When the assignments differ you will have mixed
|
||
Master and Backup IPs on both machines.
|
||
|
||
Our example uses three interfaces, which all have a rather basic setup.
|
||
|
||
.. rubric:: Master
|
||
:name: master
|
||
|
||
|
||
Go to interfaces, make sure you have all three interfaces assigned and
|
||
setup the following addresses and subnets:
|
||
|
||
+-----------------------+
|
||
| LAN 192.168.1.10/24 |
|
||
+-----------------------+
|
||
| WAN 172.18.0.101/24 |
|
||
+-----------------------+
|
||
| PFSYNC 10.0.0.1 |
|
||
+-----------------------+
|
||
|
||
Next we need to make sure the appropriate protocols can be used on the
|
||
different interfaces, go to :menuselection:`Firewall --> Rules` and make sure both LAN and
|
||
WAN accept at least CARP packets (see protocol selection). Because we're
|
||
connecting both firewalls using a direct cable connection, we will add a
|
||
single rule to accept all traffic on all protocols for that specific
|
||
interface. Another option is to only accept traffic to the GUI port and
|
||
pfSync protocol.
|
||
|
||
.. rubric:: Backup
|
||
:name: backup
|
||
|
||
The backup server needs its own dedicated addresses, we will use these:
|
||
|
||
+----------+-------------------+
|
||
| LAN | 192.168.1.20/24 |
|
||
+----------+-------------------+
|
||
| WAN | 172.18.0.102/24 |
|
||
+----------+-------------------+
|
||
| PFSYNC | 10.0.0.2 |
|
||
+----------+-------------------+
|
||
|
||
.. Note::
|
||
Per default the dropdown menu for subnet mask only fits for IPv4
|
||
addresses (up to 32). If you want to add an IPv6 CARP address,
|
||
write you v6 address and the dropdown list will auto-update to
|
||
itself up to 128.
|
||
|
||
Because we are going to synchronize firewall settings between both
|
||
hosts, we only need to make sure that the pfSync interface can accept
|
||
data from the master for the initial setup. Use the same rule as used
|
||
for the master on this interface.
|
||
|
||
-----------------
|
||
Setup Virtual IPs
|
||
-----------------
|
||
|
||
On the master node we are going to setup our Virtual IP addresses, which
|
||
will also be added to the backup node with a higher skew after synchronisation.
|
||
Go to :menuselection:`Interfaces --> Virtual IPs` and add a new one with the following
|
||
characteristics:
|
||
|
||
+-------------------------+------------------------------------+
|
||
| Type | Carp |
|
||
+-------------------------+------------------------------------+
|
||
| Interface | WAN |
|
||
+-------------------------+------------------------------------+
|
||
| IP addresses | 172.18.0.100 / 24 |
|
||
+-------------------------+------------------------------------+
|
||
| Virtual password | opnsense (the example uses this) |
|
||
+-------------------------+------------------------------------+
|
||
| VHID Group | 1 |
|
||
+-------------------------+------------------------------------+
|
||
| Advertising Frequency | Base 1 / Skew 0 |
|
||
+-------------------------+------------------------------------+
|
||
| Description | VIP WAN |
|
||
+-------------------------+------------------------------------+
|
||
|
||
And another using the following:
|
||
|
||
+-------------------------+------------------------------------+
|
||
| Type | Carp |
|
||
+-------------------------+------------------------------------+
|
||
| Interface | LAN |
|
||
+-------------------------+------------------------------------+
|
||
| IP addresses | 192.168.1.1 / 24 |
|
||
+-------------------------+------------------------------------+
|
||
| Virtual password | opnsense (the example uses this) |
|
||
+-------------------------+------------------------------------+
|
||
| VHID Group | 3 |
|
||
+-------------------------+------------------------------------+
|
||
| Advertising Frequency | Base 1 / Skew 0 |
|
||
+-------------------------+------------------------------------+
|
||
| Description | VIP LAN |
|
||
+-------------------------+------------------------------------+
|
||
|
||
------------------
|
||
Setup outbound NAT
|
||
------------------
|
||
|
||
When traffic is going out of the firewall it should also use the virtual
|
||
IP address on the WAN interface to make seamless transitions possible. The
|
||
default NAT configuration is for OPNsense is to use Automatic outbound NAT
|
||
rule generation using the WAN interface's IP address for outgoing connections.
|
||
This will not allow seamless transitions and needs to be changed to the WAN
|
||
VIP.
|
||
|
||
Go to :menuselection:`Firewall --> NAT --> Outbound`. Choose manual outbound
|
||
nat rule generation. On this page create the a rule originating from the
|
||
192.168.1.0/24 network to use the CARP virtual interface (172.18.0.100).
|
||
The rule should contain the following:
|
||
|
||
+-------------------------+------------------------------------+
|
||
| Interface | WAN |
|
||
+-------------------------+------------------------------------+
|
||
| Source addresss | LAN net (192.168.1.0/24) |
|
||
+-------------------------+------------------------------------+
|
||
| Translation / target | 172.18.0.100 (CARP virtual IP) |
|
||
+-------------------------+------------------------------------+
|
||
|
||
----------------------------
|
||
(optional) Setup DHCP server
|
||
----------------------------
|
||
|
||
When using DHCP for the local area network, there are some things to
|
||
consider. All clients should use the virtual address instead of the
|
||
physical address it's normally propagating. Next thing to consider is
|
||
there will be two servers active at the same time, which should know of
|
||
each others pools. If DNS requests are also forwarded by OPNsense, make
|
||
sure the DHCP server sends the right IP address. These are settings used
|
||
in our example (on the master server):
|
||
|
||
+--------------------+----------------+
|
||
| DNS servers | 192.168.1.1 |
|
||
+--------------------+----------------+
|
||
| Gateway | 192.168.1.1 |
|
||
+--------------------+----------------+
|
||
| Failover peer IP | 192.168.1.20 |
|
||
+--------------------+----------------+
|
||
|
||
---------------------------------
|
||
Setup pfSync and HA sync (xmlrpc)
|
||
---------------------------------
|
||
|
||
First we should configure pfSync to synchronize the connection state tables and
|
||
HA sync (xmlrpc) on the master firewall. Go to
|
||
:menuselection:`System --> High Availability --> Settings` and enable pfSync by
|
||
activating the `Synchronize States` checkbox, selecting PFSYNC for the
|
||
`Synchronize Interface` and enter the peer IP (10.0.0.2) in the field
|
||
`Synchronize Peer IP`.
|
||
|
||
To synchronize the configuration settings from the master to the backup
|
||
firewall, we setup the XMLRPC sync. In the `Synchronize Config to IP` field
|
||
we enter the peer IP (10.0.0.2) of the PFSYNC interface again to keep this
|
||
traffic on the direct connection between the two firewalls. Now we need to
|
||
enter the remote user name and password and configure the settings we want to
|
||
duplicate to the backup server. For our setup we will enable the following:
|
||
|
||
+---------------------------+
|
||
| Synchronize rules |
|
||
+---------------------------+
|
||
| Synchronize NAT |
|
||
+---------------------------+
|
||
| Synchronize DHCPD |
|
||
+---------------------------+
|
||
| Synchronize Virtual IPs |
|
||
+---------------------------+
|
||
|
||
After this we configure pfSync on the backup firewall. Go to
|
||
:menuselection:`System --> High Availability --> Settings` and enable pfSync by
|
||
activating the `Synchronize States` checkbox, selecting PFSYNC for the
|
||
`Synchronize Interface` and enter the master IP (10.0.0.1) in the field
|
||
`Synchronize Peer IP`. Do not configure XMLRPC sync on the backup firewall.
|
||
|
||
--------------
|
||
Finalize setup
|
||
--------------
|
||
|
||
Just to make sure all settings are properly applied, reboot both
|
||
firewalls before testing.
|
||
|
||
-------------
|
||
Testing setup
|
||
-------------
|
||
|
||
First go to :menuselection:`System --> High availability --> Status` in the OPNsense webinterface and check if
|
||
both machines are properly initialized.
|
||
|
||
To test our setup, we will connect a client to the local area network
|
||
and open a ssh connection to a host behind both firewalls. Now when
|
||
connected you should be able to look at the state table on both OPNsense
|
||
firewalls (:menuselection:`Firewall --> Diagnostics --> States Dump`) and they should both display the same
|
||
connection. Next try to pull the network plug from the master firewall
|
||
and it should move over to the backup without loosing (or freezing) the
|
||
ssh connection.
|
||
|
||
------------------------
|
||
Adding multiple CARP IPs
|
||
------------------------
|
||
|
||
If your provider offers you a subnet of public IP addresses and you
|
||
want to expose them for NAT or different services running on your
|
||
Firewall, you will also have to add them to your HA setup.
|
||
Since adding a VHID for every IP would make the CARP traffic very noisy,
|
||
you can also add a new IP Alias and choose the correct VHID where the
|
||
first CARP IP is configured.
|
||
|
||
.. Note::
|
||
IP Alias is not synchronized to slave, be sure to also add it to your
|
||
second machine.
|
||
|
||
-----------------------------------
|
||
Example: Updating a CARP HA Cluster
|
||
-----------------------------------
|
||
|
||
Running a redundant Active/Passive cluster leads to the expectation to have zero
|
||
downtime. To keep the downtime at a minimum when running updates just follow
|
||
these steps:
|
||
|
||
- Update your secondary unit and wait until it is online again
|
||
- On your primary unit go to :menuselection:`Interfaces --> Virtual IPs --> Status` and click **Enter Persistent CARP Maintenance Mode**
|
||
- You secondary unit is now *MASTER*, check if all services like DHCP, VPN, NAT are working correctly
|
||
- If you ensured the update was fine, update your primary unit and hit **Leave Persistent CARP Maintenance Mode**
|
||
|
||
With these steps you will not lose too many packets and your existing connection will be transferred as well.
|
||
Also note that entering persistent mode survives a reboot.
|
||
|
||
---------
|
||
Resources
|
||
---------
|
||
|
||
#. Configuration for master server ( :download:`Carp_example_master.xml <resources/Carp_example_master.xml>` )
|
||
#. Configuration for backup server ( :download:`Carp_example_backup.xml <resources/Carp_example_backup.xml>` )
|