|
|
|
===========================
|
|
|
|
Setup a routed IPSec Tunnel
|
|
|
|
===========================
|
|
|
|
|
|
|
|
Most Site-to-Site VPNs are policy-based, which means you define a local and a remote
|
|
|
|
network (or group of networks). Only traffic matching the defined policy is pushed into the
|
|
|
|
VPN tunnel. As the demands for more complex and fault tolerant VPN scenarios growed over the
|
|
|
|
years, most major router vendors implemented a kind of VPN, the route-based IPSec.
|
|
|
|
|
|
|
|
The difference is that local and remote network is just 0.0.0.0/0, so anything can travel
|
|
|
|
through the tunnel, it just needs a route. A new Virtual Tunnel Interface (VTI) has to be used
|
|
|
|
for this.
|
|
|
|
|
|
|
|
There are two benefits for this kind of VPN:
|
|
|
|
|
|
|
|
First, you can set up two tunnels to the same gateway and failover when one line goes down.
|
|
|
|
Second, you can run dynamic routing protocols over the tunnel to create more redundant,
|
|
|
|
or software-defined networks.
|
|
|
|
|
|
|
|
----------------
|
|
|
|
Before you start
|
|
|
|
----------------
|
|
|
|
Before starting with the configuration of an IPsec tunnel you need to have a
|
|
|
|
working OPNsense installation wit a unique LAN IP subnet for each side of your
|
|
|
|
connection (your local network needs a different one than the remote network).
|
|
|
|
|
|
|
|
------------
|
|
|
|
Sample Setup
|
|
|
|
------------
|
|
|
|
For the sample configuration we use two OPNsense boxes to simulate a site to site
|
|
|
|
tunnel, with the following configuration:
|
|
|
|
|
|
|
|
.. sidebar:: Network Site A
|
|
|
|
|
|
|
|
.. nwdiag::
|
|
|
|
:scale: 100%
|
|
|
|
|
|
|
|
nwdiag {
|
|
|
|
|
|
|
|
span_width = 90;
|
|
|
|
node_width = 180;
|
|
|
|
Internet [shape = "cisco.cloud"];
|
|
|
|
pclana [label="PC Site A",shape="cisco.pc"];
|
|
|
|
pclana -- switchlana;
|
|
|
|
|
|
|
|
network LANA {
|
|
|
|
switchlana [label="",shape = "cisco.workgroup_switch"];
|
|
|
|
label = " LAN Site A";
|
|
|
|
address ="192.168.1.1.x/24";
|
|
|
|
fw1 [address="192.168.1.1/24"];
|
|
|
|
tunnel [label=" IPsec Tunnel",shape = cisco.cloud];
|
|
|
|
}
|
|
|
|
|
|
|
|
network WANA {
|
|
|
|
label = " WAN Site A";
|
|
|
|
fw1 [shape = "cisco.firewall", address="1.2.3.4/24"];
|
|
|
|
Internet;
|
|
|
|
}
|
|
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
Site A
|
|
|
|
------
|
|
|
|
==================== =============================
|
|
|
|
**Hostname** fw1
|
|
|
|
**WAN IP** 1.2.3.4/24
|
|
|
|
**LAN IP** 192.168.1.1/24
|
|
|
|
**LAN DHCP Range** 192.168.1.100-192.168.1.200
|
|
|
|
==================== =============================
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
.. sidebar:: Network Site B
|
|
|
|
|
|
|
|
.. nwdiag::
|
|
|
|
:scale: 100%
|
|
|
|
|
|
|
|
nwdiag {
|
|
|
|
|
|
|
|
span_width = 90;
|
|
|
|
node_width = 180;
|
|
|
|
Internet [shape = "cisco.cloud"];
|
|
|
|
pclanb [label="PC Site B",shape="cisco.pc"];
|
|
|
|
pclanb -- switchlanb;
|
|
|
|
|
|
|
|
network LANB {
|
|
|
|
label = " LAN Site B";
|
|
|
|
address ="192.168.2.1.x/24";
|
|
|
|
fw2 [address="192.168.2.1/24"];
|
|
|
|
tunnel [label=" IPsec Tunnel",shape = cisco.cloud];
|
|
|
|
switchlanb [label="",shape = "cisco.workgroup_switch"];
|
|
|
|
}
|
|
|
|
|
|
|
|
network WANB {
|
|
|
|
label = " WAN Site B";
|
|
|
|
fw2 [shape = "cisco.firewall", address="4.3.2.1/24"];
|
|
|
|
Internet;
|
|
|
|
}
|
|
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
Site B
|
|
|
|
------
|
|
|
|
|
|
|
|
==================== =============================
|
|
|
|
**Hostname** fw2
|
|
|
|
**WAN IP** 4.3.2.1/24
|
|
|
|
**LAN Net** 192.168.2.0/24
|
|
|
|
**LAN DHCP Range** 192.168.2.100-192.168.2.200
|
|
|
|
==================== =============================
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
|
|
|
|
Full Network Diagram Including IPsec Tunnel
|
|
|
|
-------------------------------------------
|
|
|
|
|
|
|
|
.. nwdiag::
|
|
|
|
:scale: 100%
|
|
|
|
:caption: IPsec Site-to-Site tunnel network
|
|
|
|
|
|
|
|
nwdiag {
|
|
|
|
|
|
|
|
span_width = 90;
|
|
|
|
node_width = 180;
|
|
|
|
Internet [shape = "cisco.cloud"];
|
|
|
|
pclana [label="PC Site A",shape="cisco.pc"];
|
|
|
|
pclana -- switchlana;
|
|
|
|
|
|
|
|
network LANA {
|
|
|
|
switchlana [label="",shape = "cisco.workgroup_switch"];
|
|
|
|
label = " LAN Site A";
|
|
|
|
address ="192.168.1.1.x/24";
|
|
|
|
fw1 [address="192.168.1.1/24"];
|
|
|
|
tunnel [label=" IPsec Tunnel",shape = cisco.cloud];
|
|
|
|
}
|
|
|
|
|
|
|
|
network WANA {
|
|
|
|
label = " WAN Site A";
|
|
|
|
fw1 [shape = "cisco.firewall", address="1.2.3.4/24"];
|
|
|
|
Internet;
|
|
|
|
}
|
|
|
|
|
|
|
|
network WANB {
|
|
|
|
label = " WAN Site B";
|
|
|
|
fw2 [shape = "cisco.firewall", address="4.3.2.1/24"];
|
|
|
|
Internet;
|
|
|
|
}
|
|
|
|
|
|
|
|
network LANB {
|
|
|
|
label = " LAN Site B";
|
|
|
|
address ="192.168.2.1.x/24";
|
|
|
|
fw2 [address="192.168.2.1/24"];
|
|
|
|
tunnel;
|
|
|
|
switchlanb [label="",shape = "cisco.workgroup_switch"];
|
|
|
|
}
|
|
|
|
pclanb [label="PC Site B",shape="cisco.pc"];
|
|
|
|
pclanb -- switchlanb;
|
|
|
|
|
|
|
|
}
|
|
|
|
|
|
|
|
---------------------------------------
|
|
|
|
Firewall Rules Site A & Site B (part 1)
|
|
|
|
---------------------------------------
|
|
|
|
To allow IPsec tunnel connections, the following should be allowed on WAN for on
|
|
|
|
sites (under :menuselection:`Firewall --> Rules --> WAN`):
|
|
|
|
|
|
|
|
* Protocol ESP
|
|
|
|
* UDP Traffic on port 500 (ISAKMP)
|
|
|
|
* UDP Traffic on port 4500 (NAT-T)
|
|
|
|
|
|
|
|
.. image:: images/ipsec_wan_rules.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
.. Note::
|
|
|
|
|
|
|
|
You can further limit the traffic by the source IP of the remote host.
|
|
|
|
|
|
|
|
-----------------------
|
|
|
|
Step 1 - Phase 1 Site A
|
|
|
|
-----------------------
|
|
|
|
(Under :menuselection:`VPN --> IPsec --> Tunnel Settings` Press **+**)
|
|
|
|
We will use the following settings:
|
|
|
|
|
|
|
|
General information
|
|
|
|
-------------------
|
|
|
|
========================= ============= ==================================================
|
|
|
|
**Connection method** default *Default is “Start on traffic”*
|
|
|
|
**Key Exchange version** V2
|
|
|
|
**Internet Protocol** IPv4
|
|
|
|
**Interface** WAN *Choose the interface connected to the internet*
|
|
|
|
**Remote gateway** 4.3.2.1 *The public IP address of your remote OPNsense*
|
|
|
|
**Description** Site B *Freely chosen description*
|
|
|
|
========================= ============= ==================================================
|
|
|
|
|
|
|
|
|
|
|
|
Phase 1 proposal (Authentication)
|
|
|
|
---------------------------------
|
|
|
|
=========================== ====================== ======================================
|
|
|
|
**Authentication method** Mutual PSK *Using a Pre-shared Key*
|
|
|
|
**My identifier** My IP address *Simple identification for fixed IP*
|
|
|
|
**Peer identifier** Peer IP address *Simple identification for fixed IP*
|
|
|
|
**Pre-Shared Key** At4aDMOAOub2NwT6gMHA *Random key*. **CREATE YOUR OWN!**
|
|
|
|
=========================== ====================== ======================================
|
|
|
|
|
|
|
|
|
|
|
|
Phase 1 proposal (Algorithms)
|
|
|
|
-----------------------------
|
|
|
|
========================== =============== ===========================================
|
|
|
|
**Encryption algorithm** AES *For our sample we will use AES/256 bits*
|
|
|
|
**Hash algoritm** SHA512 *Use a strong hash like SHA512*
|
|
|
|
**DH key group** 14 (2048 bit) *2048 bit should be sufficient*
|
|
|
|
**Lifetime** 28800 sec *Lifetime before renegotiation*
|
|
|
|
========================== =============== ===========================================
|
|
|
|
|
|
|
|
|
|
|
|
Advanced Options
|
|
|
|
----------------
|
|
|
|
======================= =========== ========================================================
|
|
|
|
**Install Policy** Unchecked *This has to be unchecked since we want plain routing*
|
|
|
|
**Disable Rekey** Unchecked *Renegotiate when connection is about to expire*
|
|
|
|
**Disable Reauth** Unchecked *For IKEv2 only re-authenticate peer on rekeying*
|
|
|
|
**NAT Traversal** Disabled *For IKEv2 NAT traversal is always enabled*
|
|
|
|
**Dead Peer Detection** Unchecked
|
|
|
|
======================= =========== ========================================================
|
|
|
|
|
|
|
|
|
|
|
|
Save your setting by pressing:
|
|
|
|
|
|
|
|
.. image:: images/btn_save.png
|
|
|
|
|
|
|
|
|
|
|
|
-----------------------
|
|
|
|
Step 2 - Phase 2 Site A
|
|
|
|
-----------------------
|
|
|
|
Press the button that says '+ Show 0 Phase-2 entries'
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_show_p2.png
|
|
|
|
|
|
|
|
You will see an empty list:
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_p2_empty.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
Now press the **+** at the right of this list to add a Phase 2 entry.
|
|
|
|
As we do not define a local and remote network, we just use tunnel addresses,
|
|
|
|
you might already know from OpenVPN. In this example we use ``10.111.1.1`` and
|
|
|
|
``10.111.1.2``. These will be the gateway addresses used for routing
|
|
|
|
|
|
|
|
General information
|
|
|
|
-------------------
|
|
|
|
======================= ================== =============================
|
|
|
|
**Mode** Route-based *Select Route-based*
|
|
|
|
**Description** Local LAN Site B *Freely chosen description*
|
|
|
|
======================= ================== =============================
|
|
|
|
|
|
|
|
Tunnel Network
|
|
|
|
--------------
|
|
|
|
======================= ================== =====================
|
|
|
|
**Local Address** Local Tunnel IP *Set IP 10.111.1.1*
|
|
|
|
**Remote Address** Remote Tunnel IP *Set IP 10.111.1.2*
|
|
|
|
======================= ================== =====================
|
|
|
|
|
|
|
|
Phase 2 proposal (SA/Key Exchange)
|
|
|
|
----------------------------------
|
|
|
|
|
|
|
|
========================== ================ =======================================
|
|
|
|
**Protocol** ESP *Choose ESP for encryption*
|
|
|
|
**Encryption algorithms** AES / 256 *For the sample we use AES 256*
|
|
|
|
**Hash algortihms** SHA512 *Choose a strong hash like SHA512*
|
|
|
|
**PFS Key group** 14 (2048 bit) *Not required but enhanced security*
|
|
|
|
**Lifetime** 3600 sec
|
|
|
|
========================== ================ =======================================
|
|
|
|
|
|
|
|
Save your settings by pressing:
|
|
|
|
|
|
|
|
.. image:: images/btn_save.png
|
|
|
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
Enable IPsec for Site A, select:
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_enable.png
|
|
|
|
|
|
|
|
Save:
|
|
|
|
|
|
|
|
.. image:: images/btn_save.png
|
|
|
|
|
|
|
|
And apply changes:
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_apply.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
------------------
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_success.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
**You are almost done configuring Site A (only some firewall settings remain, which will be addressed later).**
|
|
|
|
**We will now proceed setting up Site B.**
|
|
|
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
-----------------------
|
|
|
|
Step 3 - Phase 1 Site B
|
|
|
|
-----------------------
|
|
|
|
(Under :menuselection:`VPN --> IPsec --> Tunnel Settings` Press **+**)
|
|
|
|
We will use the following settings:
|
|
|
|
|
|
|
|
General information
|
|
|
|
-------------------
|
|
|
|
========================= ============= ==================================================
|
|
|
|
**Connection method** Default *Default is 'Start on traffic'*
|
|
|
|
**Key Exchange version** V2
|
|
|
|
**Internet Protocol** IPv4
|
|
|
|
**Interface** WAN *Choose the interface connected to the internet*
|
|
|
|
**Remote gateway** 1.2.3.4 *The public IP address of your remote OPNsense*
|
|
|
|
**Description** Site A *Freely chosen description*
|
|
|
|
========================= ============= ==================================================
|
|
|
|
|
|
|
|
|
|
|
|
Phase 1 proposal (Authentication)
|
|
|
|
---------------------------------
|
|
|
|
=========================== ====================== ======================================
|
|
|
|
**Authentication method** Mutual PSK *Using a Pre-shared Key*
|
|
|
|
**My identifier** My IP address *Simple identification for fixed ip*
|
|
|
|
**Peer identifier** Peer IP address *Simple identification for fixed ip*
|
|
|
|
**Pre-Shared Key** At4aDMOAOub2NwT6gMHA *Random key*. **CREATE YOUR OWN!**
|
|
|
|
=========================== ====================== ======================================
|
|
|
|
|
|
|
|
|
|
|
|
Phase 1 proposal (Algorithms)
|
|
|
|
-----------------------------
|
|
|
|
========================== =============== ===========================================
|
|
|
|
**Encryption algorithm** AES *For our sample we will use AES/256 bits*
|
|
|
|
**Hash algoritm** SHA512 *Use a strong hash like SHA512*
|
|
|
|
**DH key group** 14 (2048 bit) *2048 bit should be sufficient*
|
|
|
|
**Lifetime** 28800 sec *Lifetime before renegotiation*
|
|
|
|
========================== =============== ===========================================
|
|
|
|
|
|
|
|
|
|
|
|
Advanced Options
|
|
|
|
----------------
|
|
|
|
======================= =========== ========================================================
|
|
|
|
**Install Policy** Unchecked *This has to be unchecked since we want plain routing*
|
|
|
|
**Disable Rekey** Unchecked *Renegotiate when connection is about to expire*
|
|
|
|
**Disable Reauth** Unchecked *For IKEv2 only re-authenticate peer on rekeying*
|
|
|
|
**NAT Traversal** Disabled *For IKEv2 NAT traversal is always enabled*
|
|
|
|
**Dead Peer Detection** Unchecked
|
|
|
|
======================= =========== ========================================================
|
|
|
|
|
|
|
|
|
|
|
|
Save your setting by pressing:
|
|
|
|
|
|
|
|
.. image:: images/btn_save.png
|
|
|
|
|
|
|
|
|
|
|
|
-----------------------
|
|
|
|
Step 4 - Phase 2 Site B
|
|
|
|
-----------------------
|
|
|
|
|
|
|
|
Press the button that says '+ Show 0 Phase-2 entries'
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_show_p2.png
|
|
|
|
|
|
|
|
You will see an empty list:
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_p2_empty.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
Now press the *+* at the right of this list to add a Phase 2 entry.
|
|
|
|
|
|
|
|
General information
|
|
|
|
-------------------
|
|
|
|
======================= ================== =============================
|
|
|
|
**Mode** Route-based *Select Route-based*
|
|
|
|
**Description** Local LAN Site A *Freely chosen description*
|
|
|
|
======================= ================== =============================
|
|
|
|
|
|
|
|
Tunnel Network
|
|
|
|
--------------
|
|
|
|
======================= ================== =====================
|
|
|
|
**Local Address** Local Tunnel IP *Set IP 10.111.1.2*
|
|
|
|
**Remote Address** Remote Tunnel IP *Set IP 10.111.1.1*
|
|
|
|
======================= ================== =====================
|
|
|
|
|
|
|
|
|
|
|
|
Phase 2 proposal (SA/Key Exchange)
|
|
|
|
----------------------------------
|
|
|
|
=========================== =============== =======================================
|
|
|
|
**Protocol** ESP *Choose ESP for encryption*
|
|
|
|
**Encryption algorithms** AES / 256 *For the sample we use AES 256*
|
|
|
|
**Hash algortihms** SHA512 *Choose a strong hash like SHA512*
|
|
|
|
**PFS Key group** 14 (2048 bit) *Not required but enhanced security*
|
|
|
|
**Lifetime** 3600 sec
|
|
|
|
=========================== =============== =======================================
|
|
|
|
|
|
|
|
|
|
|
|
Save your setting by pressing:
|
|
|
|
|
|
|
|
.. image:: images/btn_save.png
|
|
|
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
Enable IPsec for Site B, Select:
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_enable.png
|
|
|
|
|
|
|
|
Save:
|
|
|
|
|
|
|
|
.. image:: images/btn_save.png
|
|
|
|
|
|
|
|
And apply changes:
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_apply.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
-----------------------------
|
|
|
|
|
|
|
|
.. image:: images/ipsec_s2s_vpn_p1a_success.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
---------------------------------------
|
|
|
|
Firewall Rules Site A & Site B (part 2)
|
|
|
|
---------------------------------------
|
|
|
|
|
|
|
|
To allow traffic passing to your LAN subnet you need to add a rule to the IPsec
|
|
|
|
interface (under :menuselection:`Firewall --> Rules --> IPsec`).
|
|
|
|
|
|
|
|
.. image:: images/ipsec_ipsec_lan_rule.png
|
|
|
|
:width: 100%
|
|
|
|
|
|
|
|
------------------
|
|
|
|
IPsec Tunnel Ready
|
|
|
|
------------------
|
|
|
|
|
|
|
|
The tunnel should now be up and routing the both networks.
|
|
|
|
Go to :menuselection:`VPN --> IPsec --> Status Overview` to see current status.
|
|
|
|
|
|
|
|
------------------------
|
|
|
|
Step 5 - Define Gateways
|
|
|
|
------------------------
|
|
|
|
|
|
|
|
Now that you have the VPN up and running you have to set up a gateway.
|
|
|
|
Go to :menuselection:`System --> Gateways --> Single` and add a new gateway.
|
|
|
|
|
|
|
|
Gateway Site-A
|
|
|
|
--------------
|
|
|
|
================= ============ ===============================================================
|
|
|
|
**Name** VPNGW *Set a name for your gateway*
|
|
|
|
**Interface** IPSEC1000 *Choose the IPsec interface*
|
|
|
|
**IP Address** 10.111.1.2 *Set the peer IP address*
|
|
|
|
**Far Gateway** Checked *This has to be checked as it is a point-to-point connection*
|
|
|
|
================= ============ ===============================================================
|
|
|
|
|
|
|
|
Gateway Site-B
|
|
|
|
--------------
|
|
|
|
================= ============ ===============================================================
|
|
|
|
**Name** VPNGW *Set a name for your gateway*
|
|
|
|
**Interface** IPSEC1000 *Choose the IPsec interface*
|
|
|
|
**IP Address** 10.111.1.1 *Set the peer IP address*
|
|
|
|
**Far Gateway** checked *This has to be checked as it is a point-to-point connection*
|
|
|
|
================= ============ ===============================================================
|
|
|
|
|
|
|
|
--------------------------
|
|
|
|
Step 5 - Add Static Routes
|
|
|
|
--------------------------
|
|
|
|
|
|
|
|
When gateways are set up you can add a route for the remote network pointing to the new gateway.
|
|
|
|
On Site-A add a route to Site-B and vice versa.
|
|
|
|
Go to :menuselection:`System --> Routes --> Configuration`.
|
|
|
|
|
|
|
|
Route Site-A
|
|
|
|
------------
|
|
|
|
===================== ================ =============================
|
|
|
|
**Network Address** 192.168.2.0/24 *Set the network of Site-B*
|
|
|
|
**Gateway** VPNGW *Select the VPN gateway*
|
|
|
|
===================== ================ =============================
|
|
|
|
|
|
|
|
Gateway Site-B
|
|
|
|
---------------
|
|
|
|
===================== ================ =============================
|
|
|
|
**Network Address** 192.168.1.0/24 *Set the network of Site-A*
|
|
|
|
**Gateway** VPNGW *Select the VPN gateway*
|
|
|
|
===================== ================ =============================
|
|
|
|
|
|
|
|
|
|
|
|
Now you are all set!
|