2019-05-03 15:01:15 +00:00
|
|
|
================
|
2019-05-03 18:09:46 +00:00
|
|
|
Other Types
|
2019-05-03 15:01:15 +00:00
|
|
|
================
|
|
|
|
|
|
|
|
|
|
Besides wired, wireless and VPN interfaces, there are also some other, virtual interfaces, as well as some
|
|
|
|
|
miscellaneous interface-related. These options can be found under :menuselection:`Interfaces --> Other types`.
|
|
|
|
|
This document briefly explains these options.
|
|
|
|
|
|
|
|
|
|
------
|
|
|
|
|
Bridge
|
|
|
|
|
------
|
|
|
|
|
|
|
|
|
|
Bridging allows to create a connection between separate networks, allow traffic on network A destined for network B
|
|
|
|
|
(where both networks are connected to your OPNsense device) to reach it via this bridge. Note that this does not
|
|
|
|
|
include DHCP services—this needs to set using :ref:`DHCP relaying <dhcp-relaying>`.
|
|
|
|
|
|
|
|
|
|
---
|
|
|
|
|
GIF
|
|
|
|
|
---
|
|
|
|
|
|
|
|
|
|
GIF (``gif(4)``, Generic Tunnel Interface) can be used to tunnel IPv6 via IPv4 connections. A common use for this are the
|
|
|
|
|
IPv6 tunnel of Hurricane Electric (he.net).
|
|
|
|
|
|
|
|
|
|
---
|
|
|
|
|
GRE
|
|
|
|
|
---
|
|
|
|
|
|
|
|
|
|
GRE (``gre(4)``, Generic Routing Encapsulation) is used to create a virtual point-to-point connection, through which
|
|
|
|
|
encapsulated packages can be sent. This can be used to utilise protocols between devices over a connection that
|
|
|
|
|
does not normally support these protocols.
|
|
|
|
|
|
|
|
|
|
----
|
|
|
|
|
LAGG
|
|
|
|
|
----
|
|
|
|
|
|
|
|
|
|
LAGG (``lagg(4)``) allows for link aggregation, bonding and fault tolerance. This works best if your network switches
|
|
|
|
|
support. Only unassigned interfaces can be added to LAGG. More information about LAGG can be found in
|
|
|
|
|
`the FreeBSD manual <https://www.freebsd.org/doc/handbook/network-aggregation.html>`_.
|
|
|
|
|
|
2019-12-05 14:45:33 +00:00
|
|
|
--------------
|
|
|
|
|
Loopback
|
|
|
|
|
--------------
|
|
|
|
|
|
|
|
|
|
Loopbacks are logical virtual interfaces which emulate real interfaces and can be used for different setup scenario's,
|
|
|
|
|
which require always-on interfaces. Below you will find some scenario's for which these types of interfaces are used.
|
|
|
|
|
|
|
|
|
|
* Administrative access to services on your machine, which can bind to an address configured on top of the loopback.
|
|
|
|
|
* Using loopback addresses as router IDs for OSPF or BGP, which helps to identify your nodes and eases administration
|
|
|
|
|
|
2019-05-03 15:01:15 +00:00
|
|
|
----
|
|
|
|
|
VLAN
|
|
|
|
|
----
|
|
|
|
|
|
|
|
|
|
VLANs (Virtual LANs) can be used to segment a single physical network into multiple virtual networks. This can be
|
|
|
|
|
done for QoS purposes, among other things. For this reason, most ISP-issued IPTV devices utilise VLANs.
|
2019-11-04 20:55:33 +00:00
|
|
|
|
|
|
|
|
|
|
|
|
|
------
|
|
|
|
|
VXLAN
|
|
|
|
|
------
|
|
|
|
|
|
|
|
|
|
Virtual eXtensible Local Area Networks (VXLANs) are used to overlay virtualized layer 2 networks over layer 3 networks
|
|
|
|
|
as described by `rfc7348 <https://tools.ietf.org/html/rfc7348>`__.
|
|
|
|
|
|
|
|
|
|
Tunnels can be setup in point to point (parameter :code:`Remote address`) or multicast (parameters :code:`Multicast group` and :code:`Device`).
|
|
|
|
|
The `Source address` must be an existing (statically assigned) address assigned at this firewall, which will be used as
|
|
|
|
|
source in the encapsulating IPv4/IPv6 header.
|
|
|
|
|
|
|
|
|
|
.. Note::
|
|
|
|
|
|
|
|
|
|
Since the vxlan interface encapsulates the Ethernet frame with an IP, UDP, and vxlan header,
|
|
|
|
|
the resulting frame may be larger than the MTU of the physical network. The vxlan specification recommends the physical
|
|
|
|
|
network MTU be configured to use jumbo frames to accommodate the encapsulated frame size.
|
|
|
|
|
Alternatively, the MTU size on the vxlan interface might be reduced to allow the encapsulated frame to fit in
|
|
|
|
|
the current MTU of the physical network.
|
