Fix#10588
Regression since #10305
While we're there, rejig the FL toggle callback shenanigans so that implementation details don't leak through to *other* implementations.
(i.e., leave the Kobo mess in Kobo land, with only a minimal impact on the public API and its implementation).
Make sure we only send Suspend/Resume events when we *actually* suspend/resume. This is done via the Device `_beforeSuspend`/`_afterResume` methods, and those were called by the *input handlers*, not the PM logic; which means they would fire, while the PM logic could actually take a smarter decision and *not* do what the event just sent implied ;).
(i.e., sleep with a cover -> suspend + actual suspend, OK; but if you then resume with a button -> input assumes resume, but PM will actually suspend again!).
Existing design issue made more apparent by #9448 ;).
Also fixes/generalizes a few corner-cases related to screen_saver_lock handling (e.g., don't allow USBMS during a lock).
And deal with the fallout of the main change to the Kobo frontlight ramp behavior ;).
* Rewrite the loop mechanism to use scheduled tasks instead of a single blocking-ish subprocess.
* Change the actual logic to be more pleasing to the eye, especially on newer devices, as those *may* natively ramp on set; and fix a bad interaction with that behavior that could lead to no ramp at all on ramp down.
* Simplify Generic's Suspend handling to deal with the refresh ordering in a saner manner. The screensaver might be visible a tad longer than before this change before the frontlight actually ramps off.
* This removes support for the following deprecated constants: `DTAP_ZONE_FLIPPING`, `DTAP_ZONE_BOOKMARK`, `DCREREADER_CONFIG_DEFAULT_FONT_GAMMA`
* The "Advanced settings" panel now highlights modified values in bold (think about:config in Firefox ;)).
* LuaData: Isolate global table lookup shenanigans, and fix a few issues in unused-in-prod codepaths.
* CodeStyle: Require module locals for Lua/C modules, too.
* ScreenSaver: Actually garbage collect our widget on close (ScreenSaver itself is not an instantiated object).
* DateTimeWidget: Code cleanups to ensure child widgets can be GC'ed.
* Disable all non power management related input during suspend. (This prevents wonky touch events from being tripped when closing a sleep cover on an already-in-suspend device, among other things).
* Kobo: Use our WakeupMgr instance, not the class.
* WakupMgr: split `removeTask` in two:
* `removeTask`, which *only* takes a queue index as input, and only removes a single task. Greatly simplifies the function (i.e., it's just a `table.remove`).
* `removeTasks`, which takes an epoch or a cb ref, and removes *every* task that matches.
* Both of these will also *always* re-schedule the next task (if any) on exit, since we can have multiple WakeupMgr tasks queued, but we can only have a single RTC wake alarm set ;).
* `wakeupAction` now takes a `proximity` argument, which it passes on to its `validateWakeupAlarmByProximity` call, allowing call sites to avoir having to duplicate that call themselves when they want to use a custom proximity window.
* `wakeupAction` now re-schedules the next task (if any) on exit.
* Simplify `Kobo:checkUnexpectedWakeup`, by removing the duplicate `WakerupMgr:validateWakeupAlarmByProximity` call, now that we can pass a proximity window to `WakeuoMgr:wakeupAction`.
* The various network activity timeouts are now halved when autostandby is enabled.
* Autostandby: get rid of the dummy deadline_guard task, as it's no longer necessary since #9009.
* UIManager: The previous change allows us to simplify `getNextTaskTimes` into a simpler `getNextTaskTime` variant, getting rid of a table & a loop.
* ReaderFooter & ReaderHeader: Make sure we only perform a single refresh when exiting standby.
* Kobo: Rewrite sysfs writes to use ANSI C via FFI instead of stdio via Lua, as it obscured some common error cases (e.g., EBUSY on /sys/power/state).
* Kobo: Simplify `suspend`, now that we have sane error handling in sysfs writes.
* Kobo.powerd: Change `isCharging` & `isAuxCharging` behavior to match the behavior of the NTX ioctl (i.e., Charging == Plugged-in). This has the added benefit of making the AutoSuspend checks behave sensibly in the "fully-charged but still plugged in" scenario (because being plugged in is enough to break PM on `!canPowerSaveWhileCharging` devices).
* AutoSuspend: Disable our `AllowStandby` handler when auto standby is disabled, so as to not interfere with other modules using `UIManager:allowStandby` (fix#9038).
* PowerD: Allow platforms to implement `isCharged`, indicating that the battery is full while still plugged in to a power source (battery icon becomes a power plug icon).
* Kobo.powerd: Implement `isCharged`, and kill charging LEDs once battery is full.
* Kindle.powerd: Implement `isCharged` on post-Wario devices. (`isCharging` is still true in that state, as it ought to).
* Rejig frontlight warmth API to more closely match the existing API, and, hopefully, clarify some of its quirks, and reduce boilerplate and duplicate code in platform implementations.
* Tweak Kindle:setDateTime to prefer using the platform's custom script, as in interacts better with the stock UI. And make the fallbacks handle old busybox versions better.
* Add Kindle PW5 support ;).
* Add warmth support to the Kindle platform.
* Random TextBoxWidget cleanups: make sure we immediately free destroyed instances.
* FrontLightWidget: Refactor to make it slightly less obnoxious to grok and update; i.e., separate layout from update, and properly separate brightness from warmth handling. Move to simpler widgets instead of reinventing the wheel.
* TextBoxWidgets: Implement `setText` to match TextWidget's API, as some callers may be using the two interchangeably (i.e., Button).
* NaturalLightWidget: Make sure we pass a string to InputText
* InputText: Add debug guards to catch bad callers not passing strings ;).
* The first few capacity reads after connecting to the cover may fail
* The PowerCover may trigger spurious move/add usb_plug uevent,
which translate into Charging events for us.
Instead of blindly lighting up the charging LED on those,
check if the device is actually charging, first.
Implement it on the Kobo Sage, for the PowerCover
TouchMenu: Display auxiliary battery status
Kobo: More accurately report the PowerCover's charging status
i.e., try to actually figure out if the auxiliary battery is charging
instead of just checking the reader's battery (because that one will
often swap between the charging and discharging state as it drains the
aux battery...).
PowerD: Use a cached timestamp when doing battery pull checks
previously: warm light stays at 100% for 3 hours and then drops by 50% per hour
now: warm light stays at 100% for 4 hours and then drops by 15% per hour
move state change event to higher level function so it will be called after powerd.is_fl_on is updated.
makes _setIntensity redundant so get rid of it
obsoletes #6667
A BackgroundRunner plugin instance will stop running
(rescheduling a check every 2 seconds) when there is no
(or no more) job to run.
Clients of this service now have to emit an event after
adding a job into PluginShare.backgroundJobs, so an
already loaded but stopped BackgroundRunner can notice
it and start running again.
sysfs_light handles every case sanely already, no need to be cute ;).
This prevents always setting the warmth when setting the FL on NL
devices with a mixer, because, besides being useless, it's also slow
(lua does mmap'ed io, so every handle requires an fstat + mmap).
It was subtly affecting the fluidity of the toggle ramp, and much less
subtly wreaking havoc on #5373 ;).
KA1 owners might want to investigate keeping the fds around one way or
another, like we do for the fl ioctl, to alleviate the overhead of doing
that for not one but three or four fds...
I won't be doing that, since I lack the hardware to test it, and FL+NL
stuff is pain.
* Do the same on Cervantes
* Bump base to pickup related ioctl tweaks
When reasonably possible, the program should only crash in debug mode.
Adds a couple of extra unit tests to prevent regressions and adds docs.
Fixes <https://github.com/koreader/koreader/issues/5356>.
This commit standardizes the various todos around the code a bit in a manner recognized by LDoc.
Besides drawing more attention by being displayed in the developer docs, they're also extractable with LDoc on the command line:
```sh
ldoc --tags todo,fixme *.lua
```
However, whether that particular usage offers any advantage over other search tools is questionable at best.
* and some random beautification
on if it's off.
Because, on the KA1, since wetting the warmth *has* to set the
brightness, it could ;).
Patch only actually needed on Kobo, as all Cervantes devices with warmth
support have a mixer, which mean they *can* set the warmth without
affecting the brightness ;).
* Don't override hw_intensity when we start with the FL off
* And add an insane workaround to make the first toggle behave sanely in this case.
* And also handle the sneakier case where the first toggle happening would not be manual, but triggered by a suspend/resume cycle.
* Make hasNaturalLight* caps safe to call without a device check. (fix#4919)
Make it clear that it's expecting the NTX implementation, though.
* Don't turn the FL on on resume if it was off on suspend
* Make sure turnOn/turnOff actually updates hw_intensity in the process where it matters, instead of just in a short lived fork ;). (fix#4923)
Companion PR to https://github.com/koreader/koreader-base/pull/884
* Basically flags devices known to be stable when using PxP inversion.
* Plus, random fix for #4870 ;).
* A few FrontLight tweaks & cleanups on Kobo:
* Moved the Kobo-specific startup status insanity to Kobo-specific init
* Made turnOff/turnOn frontlight do a smooth ramp down/up
* On Kobo, use turnOff/turnOn for suspend/resume, to get that smooth toggle
* On Kobo, for NaturalLight w/ a mixer, only set warmth for setWarmth, and only set Brightness for setBrightness, otherwise, it tried to set both with not in-sync values, which made the FL widget jittery.
* Enforce a known rotation on startup, to make sure we handle touch input coordinates properly.
* Proper FrontLight warmth support (thanks to @cairnsh & @pazos in #4291)!
* Fix the PageTurn buttons mapping to match Nickel's defaults
* Properly remap PageTurn buttons depending on the current rotation.
* Actually enable the Mk.7 screen refresh codepath on *all* Mk.7 devices (I'd messed up the device check...).
* Full accelerometer handling (includes a touch of refactoring regarding orientation handling in general).
* Fix insidiously broken USBMS behavior in Nickel after we exit on FW >4.8.
Fix#4291Fix#3002
Add support in nickel_conf to save/retrieve setting of
'autoColorEnabled', which is the automatic warmth feature in
Nickel. We do not support reading of 'BedTime', because it is encoded
as a QVariant. This setting is hence saved/loaded solely in/from
G_reader_settings.
This is the first step to support "automatic warmth", meaning that
warmth will be set according to the current time. The user can set a
"bedtime" at which warmth should be maximal. Warmth will increase
towards approaching bedtime and decrease afterwards.
Add new members 'auto_warmth' and 'max_warmth_hour' which tell if this
feature is enabled and the "bedtime", resp. Add a method
'calculateAutoWarmth' which will set the current warmth according to
the current time. The progression is linear but not symmetrical: we
start 5h before "bedtime", but turn back warmth to '0' 2h after it, to
make sure that warmth is '0' in the morning.
For automatically setting warmth in the background we use the
backgroundrunner plugin, because not only is it more comfortable to
use, but we also cannot require 'uimanager' during device
initialization.
If the device has natural light support (currently only KA1), use the
sysfs interface instead of the ioctl-based one. It might also be
usable on other Kobo devices for setting brightness without natural
light, but since I cannot test this, this is currently restricted to
the KA1.
* frontlight on kobo: a few fixes
Rewritten to not update NickelConf on every change, and never
if KOBO_SYNC_BRIGHTNESS_WITH_NICKEL = false.
Reintroduce global settings frontlight_intensity and
is_frontlight_on to keep level and state across koreader
sessions.
Fix a few of the remaining issues on kobo light.
Ensure settings are saved when rebooting/powering off from
File browser.
* Ensure untoggle works when starting with light off
