i2pd configuration ================== Command line options -------------------- * --conf= - Config file (default: ~/.i2pd/i2p.conf or /var/lib/i2pd/i2p.conf) This parameter will be silently ignored if the specified config file does not exist. Options specified on the command line take precedence over those in the config file. * --tunconf= - Tunnels Config file (default: ~/.i2pd/tunnels.cfg or /var/lib/i2pd/tunnels.cfg) * --pidfile= - Where to write pidfile (dont write by default) * --log - Enable or disable logging to file. 1 for yes, 0 for no. * --logfile= - Path to logfile (stdout if not set, autodetect if daemon) * --loglevel= - Log messages above this level (debug, *info, warn, error) * --host= - The external IP (deprecated) * --port= - The port to listen on * --daemon - Enable or disable daemon mode. 1 for yes, 0 for no. * --svcctl= - Windows service management (--svcctl="install" or --svcctl="remove") * --service - Use system folders (/var/run/i2pd.pid, /var/log/i2pd.log, /var/lib/i2pd). * --ipv6 - Enable communication through ipv6, off by default * --notransit - Router will not accept transit tunnels at startup. 0 by default * --floodfill - Router will be floodfill, off by default * --bandwidth= - L if bandwidth is limited to 32Kbs/sec, O - to 256Kbs/sec, P - unlimited This option will be ignored if --floodfill given * --http.address= - The address to listen on (HTTP server) * --http.port= - The port to listen on (HTTP server) * --httpproxy.address= - The address to listen on (HTTP Proxy) * --httpproxy.port= - The port to listen on (HTTP Proxy) 4446 by default * --httpproxy.keys= - optional keys file for proxy local destination (both HTTP and SOCKS) * --socksproxy.address= - The address to listen on (SOCKS Proxy) * --socksproxy.port= - The port to listen on (SOCKS Proxy). 4447 by default * --socksproxy.keys= - optional keys file for proxy local destination (both HTTP and SOCKS) * --socksproxy.outproxy= - Address of outproxy. requests outside i2p will go there * --socksproxy.outproxyport= - Outproxy remote port * --sam.address= - The address to listen on (SAM bridge) * --sam.port= - Port of SAM bridge. Usually 7656. SAM is off if not specified * --bob.address= - The address to listen on (BOB command channel) * --bob.port= - Port of BOB command channel. Usually 2827. BOB is off if not specified * --i2pcontrol.address= - The address to listen on (I2P control service) * --i2pcontrol.port= - Port of I2P control service. Usually 7650. I2PControl is off if not specified Config files ------------ INI-like, syntax is the following : = . Comments are "#", not ";" as you may expect. See [boost ticket](https://svn.boost.org/trac/boost/ticket/808) All command-line parameters are allowed as keys, but note for those which contains dot (.). For example: i2p.conf: # comment log = yes ipv6 = yes # settings for specific module [httpproxy] port = 4444 # ^^ this will be --httproxy.port= in cmdline # another one [sam] enabled = yes tunnels.cfg (filename of this config is subject of change): # outgoing tunnel sample, to remote service # mandatory parameters: # * type -- always "client" # * port -- local port to listen to # * destination -- i2p hostname # optional parameters (may be omitted) # * keys -- our identity, if unset, will be generated on every startup, # if set and file missing, keys will be generated and placed to this file # * address -- local interface to bind # * signaturetype -- signature type for new destination. 0,1 or 7 [IRC] type = client address = 127.0.0.1 port = 6668 destination = irc.postman.i2p keys = irc-keys.dat # # incoming tunnel sample, for local service # mandatory parameters: # * type -- "server" or "http" # * host -- ip address of our service # * port -- port of our service # * keys -- file with LeaseSet of address in i2p # optional parameters (may be omitted) # * inport -- optional, i2p service port, if unset - the same as 'port' # * accesslist -- comma-separated list of i2p addresses, allowed to connect # every address is b32 without '.b32.i2p' part [LOCALSITE] type = http host = 127.0.0.1 port = 80 keys = site-keys.dat [IRC-SERVER] type = server host = 127.0.0.1 port = 6667 keys = irc.dat Also see [this page](https://github.com/PurpleI2P/i2pd/wiki/tunnels.cfg) for more tunnel examples.