* 1) All the sprites in a railset MUST be in the same order. This order * is determined by normal rail. Check sprites 1005 and following for this order
* 2) The position where the railtype is loaded must always be the same, otherwise * the offset will fail.
* @note: Something more flexible might be desirable in the future. */ SpriteID total_offset; /** * Bridge offset */ SpriteID bridge_offset; /** * Offset to add to ground sprite when drawing custom waypoints / stations */ byte custom_ground_offset; } RailtypeInfo; extern RailtypeInfo _railtypes[RAILTYPE_END]; // these are the maximums used for updating signal blocks, and checking if a depot is in a pbs block enum { NUM_SSD_ENTRY = 256, // max amount of blocks NUM_SSD_STACK = 32 ,// max amount of blocks to check recursively }; /** * Maps a Trackdir to the corresponding TrackdirBits value */ static inline TrackdirBits TrackdirToTrackdirBits(Trackdir trackdir) { return (TrackdirBits)(1 << trackdir); } /** * These functions check the validity of Tracks and Trackdirs. assert against * them when convenient. */ static inline bool IsValidTrack(Track track) { return track < TRACK_END; } static inline bool IsValidTrackdir(Trackdir trackdir) { return (TrackdirToTrackdirBits(trackdir) & TRACKDIR_BIT_MASK) != 0; } /** * Functions to map tracks to the corresponding bits in the signal * presence/status bytes in the map. You should not use these directly, but * wrapper functions below instead. XXX: Which are these? */ /** * Maps a trackdir to the bit that stores its status in the map arrays, in the * direction along with the trackdir. */ extern const byte _signal_along_trackdir[TRACKDIR_END]; static inline byte SignalAlongTrackdir(Trackdir trackdir) {return _signal_along_trackdir[trackdir];} /** * Maps a trackdir to the bit that stores its status in the map arrays, in the * direction against the trackdir. */ static inline byte SignalAgainstTrackdir(Trackdir trackdir) { extern const byte _signal_against_trackdir[TRACKDIR_END]; return _signal_against_trackdir[trackdir]; } /** * Maps a Track to the bits that store the status of the two signals that can * be present on the given track. */ static inline byte SignalOnTrack(Track track) { extern const byte _signal_on_track[TRACK_END]; return _signal_on_track[track]; } /* * Functions describing logical relations between Tracks, TrackBits, Trackdirs * TrackdirBits, Direction and DiagDirections. * * TODO: Add #unndefs or something similar to remove the arrays used below * from the global scope and expose direct uses of them. */ /** * Maps a trackdir to the reverse trackdir. */ static inline Trackdir ReverseTrackdir(Trackdir trackdir) { return (Trackdir)(trackdir ^ 8); } /** * Returns the Track that a given Trackdir represents */ static inline Track TrackdirToTrack(Trackdir trackdir) { return (Track)(trackdir & 0x7); } /** * Returns a Trackdir for the given Track. Since every Track corresponds to * two Trackdirs, we choose the one which points between NE and S. * Note that the actual implementation is quite futile, but this might change * in the future. */ static inline Trackdir TrackToTrackdir(Track track) { return (Trackdir)track; } /** * Returns a TrackdirBit mask that contains the two TrackdirBits that * correspond with the given Track (one for each direction). */ static inline TrackdirBits TrackToTrackdirBits(Track track) { Trackdir td = TrackToTrackdir(track); return (TrackdirBits)(TrackdirToTrackdirBits(td) | TrackdirToTrackdirBits(ReverseTrackdir(td))); } /** * Discards all directional information from the given TrackdirBits. Any * Track which is present in either direction will be present in the result. */ static inline TrackBits TrackdirBitsToTrackBits(TrackdirBits bits) { return (TrackBits)(bits | (bits >> 8)); } /** * Maps a trackdir to the trackdir that you will end up on if you go straight * ahead. This will be the same trackdir for diagonal trackdirs, but a * different (alternating) one for straight trackdirs */ static inline Trackdir NextTrackdir(Trackdir trackdir) { extern const Trackdir _next_trackdir[TRACKDIR_END]; return _next_trackdir[trackdir]; } /** * Maps a track to all tracks that make 90 deg turns with it. */ static inline TrackBits TrackCrossesTracks(Track track) { extern const TrackBits _track_crosses_tracks[TRACK_END]; return _track_crosses_tracks[track]; } /** * Maps a trackdir to the (4-way) direction the tile is exited when following * that trackdir. */ static inline DiagDirection TrackdirToExitdir(Trackdir trackdir) { extern const DiagDirection _trackdir_to_exitdir[TRACKDIR_END]; return _trackdir_to_exitdir[trackdir]; } /** * Maps a track and an (4-way) dir to the trackdir that represents the track * with the exit in the given direction. */ static inline Trackdir TrackExitdirToTrackdir(Track track, DiagDirection diagdir) { extern const Trackdir _track_exitdir_to_trackdir[TRACK_END][DIAGDIR_END]; return _track_exitdir_to_trackdir[track][diagdir]; } /** * Maps a track and an (4-way) dir to the trackdir that represents the track * with the exit in the given direction. */ static inline Trackdir TrackEnterdirToTrackdir(Track track, DiagDirection diagdir) { extern const Trackdir _track_enterdir_to_trackdir[TRACK_END][DIAGDIR_END]; return _track_enterdir_to_trackdir[track][diagdir]; } /** * Maps a track and a full (8-way) direction to the trackdir that represents * the track running in the given direction. */ static inline Trackdir TrackDirectionToTrackdir(Track track, Direction dir) { extern const Trackdir _track_direction_to_trackdir[TRACK_END][DIR_END]; return _track_direction_to_trackdir[track][dir]; } /** * Maps a (4-way) direction to the diagonal trackdir that runs in that * direction. */ static inline Trackdir DiagdirToDiagTrackdir(DiagDirection diagdir) { extern const Trackdir _dir_to_diag_trackdir[DIAGDIR_END]; return _dir_to_diag_trackdir[diagdir]; } extern const TrackdirBits _exitdir_reaches_trackdirs[DIAGDIR_END]; /** * Returns all trackdirs that can be reached when entering a tile from a given * (diagonal) direction. This will obviously include 90 degree turns, since no * information is available about the exact angle of entering */ static inline TrackdirBits DiagdirReachesTrackdirs(DiagDirection diagdir) { return _exitdir_reaches_trackdirs[diagdir]; } /** * Returns all tracks that can be reached when entering a tile from a given * (diagonal) direction. This will obviously include 90 degree turns, since no * information is available about the exact angle of entering */ static inline TrackBits DiagdirReachesTracks(DiagDirection diagdir) { return TrackdirBitsToTrackBits(DiagdirReachesTrackdirs(diagdir)); } /** * Maps a trackdir to the trackdirs that can be reached from it (ie, when * entering the next tile. This will include 90 degree turns! */ static inline TrackdirBits TrackdirReachesTrackdirs(Trackdir trackdir) { return _exitdir_reaches_trackdirs[TrackdirToExitdir(trackdir)]; } /* Note that there is no direct table for this function (there used to be), * but it uses two simpeler tables to achieve the result */ /** * Maps a trackdir to all trackdirs that make 90 deg turns with it. */ static inline TrackdirBits TrackdirCrossesTrackdirs(Trackdir trackdir) { extern const TrackdirBits _track_crosses_trackdirs[TRACKDIR_END]; return _track_crosses_trackdirs[TrackdirToTrack(trackdir)]; } /* Checks if a given Track is diagonal */ static inline bool IsDiagonalTrack(Track track) { return (track == TRACK_X) || (track == TRACK_Y); } /* Checks if a given Trackdir is diagonal. */ static inline bool IsDiagonalTrackdir(Trackdir trackdir) { return IsDiagonalTrack(TrackdirToTrack(trackdir)); } /** * Returns a pointer to the Railtype information for a given railtype * @param railtype the rail type which the information is requested for * @return The pointer to the RailtypeInfo */ static inline const RailtypeInfo *GetRailTypeInfo(RailType railtype) { assert(railtype < RAILTYPE_END); return &_railtypes[railtype]; } /** * Checks if an engine of the given RailType can drive on a tile with a given * RailType. This would normally just be an equality check, but for electric * rails (which also support non-electric engines). * @return Whether the engine can drive on this tile. * @param enginetype The RailType of the engine we are considering. * @param tiletype The RailType of the tile we are considering. */ static inline bool IsCompatibleRail(RailType enginetype, RailType tiletype) { return HASBIT(GetRailTypeInfo(enginetype)->compatible_railtypes, tiletype); } static inline bool HasPowerOnRail(RailType enginetype, RailType tiletype) { return HASBIT(GetRailTypeInfo(enginetype)->powered_railtypes, tiletype); } /** * Checks if the given tracks overlap, ie form a crossing. Basically this * means when there is more than one track on the tile, exept when there are * two parallel tracks. * @param bits The tracks present. * @return Whether the tracks present overlap in any way. */ static inline bool TracksOverlap(TrackBits bits) { /* With no, or only one track, there is no overlap */ if (bits == 0 || KILL_FIRST_BIT(bits) == 0) return false; /* We know that there are at least two tracks present. When there are more * than 2 tracks, they will surely overlap. When there are two, they will * always overlap unless they are lower & upper or right & left. */ return bits != TRACK_BIT_HORZ && bits != TRACK_BIT_VERT; } void DrawTrainDepotSprite(int x, int y, int image, RailType railtype); void DrawDefaultWaypointSprite(int x, int y, RailType railtype); /** * Draws overhead wires and pylons for electric railways. * @param ti The TileInfo struct of the tile being drawn * @see DrawCatenaryRailway */ void DrawCatenary(const TileInfo *ti); uint GetRailFoundation(Slope tileh, TrackBits bits); #endif /* RAIL_H */