Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping activated and set to x=40hz and y=50hz
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated and set to x 40hz and y 50hz.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- Laser functionality
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release as LA does not work with Marlin 2.0.8 and TMC2208_standalone
- Input Shaping deactivated in this release as IS is not supported with Marlin 2.0.8
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed z home position after autoleveling from Z=0 to Z=5 so your nozzle does not got to your zero Z-Offset after autoleveling
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- Laser functionality
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release as LA does not work with Marlin 2.0.8 and TMC2208_standalone
- Input Shaping deactivated in this release as IS is not supported with Marlin 2.0.8
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed z home position after autoleveling from Z=0 to Z=5 so your nozzle does not got to your zero Z-Offset after autoleveling
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- Laser functionality
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release as LA does not work with Marlin 2.0.8 and TMC2208_standalone
- Input Shaping deactivated in this release as IS is not supported with Marlin 2.0.8
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
- fixed manual bed leveling point 1 from x=117 to y=117 to x=117.5 to y=117.5
- fixed z home position after autoleveling from Z=0 to Z=5 so your nozzle does not got to your zero Z-Offset after autoleveling
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets - here #define NOZZLE_TO_PROBE_OFFSET_Y 0
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated and set to x=40hz y=50hz
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping deactivated in this release, use other of my binarys for IS.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping activated and set to x=40hz and y=50hz
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated and set to x 40hz and y 50hz.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets - here #define NOZZLE_TO_PROBE_OFFSET_Y 0
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but is set to x=40hz and y=50hz.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping deactivated in this release, use other of my binarys for IS.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance disabled
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated and set to x 40hz and y 50hz.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets - here #define NOZZLE_TO_PROBE_OFFSET_Y 0
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but set to x=40 y=50
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping deactivated in this release, use other of my binarys for IS.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Marlin 2.1.x with my tweaks no LA - F4
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping activated and set to x=40hz and y=50hz
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated and set to x 40hz and y 50hz.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets - here #define NOZZLE_TO_PROBE_OFFSET_Y 0
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but set to x=40 y=50
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping deactivated in this release, use other of my binarys for IS.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance deactivated in this release, use other of my binarys for LA.
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F4 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping disabled in this release
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets - here #define NOZZLE_TO_PROBE_OFFSET_Y 0
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Marlin 2.1.x with my tweaks no LA - F1
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance disabled
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
Hi all,
as there is a firmware out for Ender 3 S1 Pro out and i am not satisfied with its basic hardware configuration i decided to release my own
firmware build for the Ender 3 S1 Pro with F1 chip.
My firmware does:
- Ender 3 S1 Pro only
- correct bed size (235x235)
- printing height 250 to respect the cable
- x-max position 235 to respect the cable
- y-max position 235 to reach every point of the bed
- correct homeing offsets
- correct nozzle to probe offsets
- Z-Offset set to 0.0 in order calibrate for your printer
- Linear Advance set to 0.06
- Input Shaping activated but set to 0. calibrate and set what you want.
- biliniear bedleveling
- probing margin bumped to 40mm to get a square mesh
- no preheat before leveling, set what you want for that before leveling.
- pidtemp and piditemp set to values of my runs with stock bed, but calibrate for your printer please
besides that this standard features of the Original Release are also active:
- 117 Set LCD Message supported
- Z Axis Microstepping set to .01 increments
- M851 and M290 changes update Z-Offset on LCD
- Z-Offset UI updates notifies host
- Restore Bedleveling after G28
- M48 Probe Repeatability Test
- Extruder minimum temperature lowered to 170C
- Heatbreak fan extruder minimum temperature set to 80C
- Probing Margin reduced to 40mm (ABL)
- Fast / Slow / Slow probing strategy
- G26 Mesh Validation
- 5 x 5 Bilinear Mesh (25 points) (ABL)
- G12 Clean the Nozzle
- Include ADC values when reporting temperature
- Emergency Parser
- Auto Report Position
- Report Fan Changes for fans that support it
- Host Action Commands
- Host Prompt Support
- M486 Cancel Objects
You will be able to print with at least 233mmx233mm with this release.
Please check your slicer settings before using it.
Your bed will now beginn at exactly x=0 and y=0.
There is no need to do any corrections in slicer like "G0 X-5".
Attached a picture with a 233x233 print for bedleveling i just did.
Its not leveled perfectly, just wanted to show the cabability to print nearly full bed...
Hope you like it.
