Update README.md

README.md

@@ -17,68 +17,7 @@ But hej. I will release the fixes. :-)
 
 
 -------------------------------------------------------------------------------------------------------------------
-My instructions for firmware installations are:
-
-- check your chip inside your printer (look at the about page, usually you will see F4 in the number FW/Ver field)
-- for F4 printer create a folder STM32F4_UPDATE on your 4096 formated SD card and put my firmware bin file inside
-- for F1 printer it is sufficient to put the firmware bin file inside the root of your 4096 formated SD card
-- reboot printer
-
-Note:
-Touch display firmware 1.0.2 or 1.0.3 is required. Look at your about page "Screen VER"
-But if you have the recent vendor firmware running you should have already one of this touch firmware versions installed and be fine.
-
-Please check your machines start gcode.
-Your bed starts now at x=0. Some Slicer default to a negative purge line start point ex x=-2 or very close to the bededge ex x=0.1.
-Put it on x=5 or something reasonable beeing good placed on your bed..
-
-Example old:
-
-G1 X-2.1 Y20 Z0.28 F5000.0 ;Move to start position
-
-G1 X-2.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
-
-G1 X-2.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
-
-G1 X-2.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
-
-
-Example new:
-
-G1 X5.1 Y20 Z0.28 F5000.0 ;Move to start position
-
-G1 X5.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
-
-G1 X5.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
-
-G1 X5.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
-
-Check also the set dimensions of the buildplate in your slicer. Most slicers have 220mm x 220 mm (Pro) or 300mm x 300mm (Plus) cause of the not
-matching firmware. The bed has 235mm x 235mm on the Pro. On the Plus we have a special situation: The nozzle can´t reach the last 5mm on y max.
-So we capped here 5mm. The configured printarea for the Plus is 310mm x 310mm.
-Please set this values as your printarea in you slicer.
-
--------------------------------------------------------------------------------------------------------------------
-
-My instructions for Z-Offset quick setting and installation:
-- level your bed with old firmware
-- note your z-offset ex. -1.74mm
-- flash new firmware
-- connect with pronterface or other terminal to your printer and issue:
-- M502 ; factory reset
-- M851 Z-1.74 ; set your z-offset
-- M500 ; save configuration
-- M503 ; check if your z-offset matches
-- G28 ; home your printer
-- heat up nozzle and/or bed like usually do before bedleveling
-- on the touch start autoleveling (there is no need to do the points if your bed was level before..)
-- after autoleveling your are ready to print.
-
-Alternative method for Z-Offset setting:
-
-Do it your way as usual. You can set your z-offset by gcode, by touch display, by other terminal. However you do it.
-This firmware is installable as every other firmware.
-
+Please read the installation.txt in the release for full update instructions!
 -------------------------------------------------------------------------------------------------------------------
 
 Be carefully with your printer. Mine works fine. But this is a new build. So have your fingers near the power button when lowering your z-axis and starting print for the first time.