Farm-Data-Relay-System/FDRS_Gateway2000/README.md

# Gateway 2.000

This is the FDRS Multiprotocol Gateway sketch. The device listens for packets over ESP-NOW, UART, LoRa, and/or MQTT, then retransmits the packets over these interfaces using rules defined in the configuration file.

The most commonly used configuration tells the device to take any ESP-NOW packet it receives and output the data over the serial port (UART):
```
#define UNIT_MAC       0x00
#define ESPNOWG_ACT    sendSerial();
```
The companion for this device, connected via serial, takes any data it receives from the serial port and sends it via MQTT:
```
#define USE_WIFI
#define SERIAL_ACT   sendMQTT();
```
Splitting the gateway into two devices allows you to use ESP-NOW and WiFi simultaneously without channel conflicts. You can also connect the first device to a computer with a USB-UART adapter and get the data that way, eliminating WiFi altogether.

If you have sensors that are out of range of your first gateway, you can use a gateway as a repeater. First you will set the ESPNOW1 address to that of your first gateway, then you'll direct general ESP-NOW traffic to the ESPNOW1 interface:
```
#define UNIT_MAC     0x01 
#define ESPNOWG_ACT  sendESPNOW(0x00);
```
![Basic](/FDRS_Gateway2000/Basic_Setup.png)


![Basic](/FDRS_Gateway2000/Basic_LoRa_Setup.png)


![Basic](/FDRS_Gateway2000/Advanced_Setup_LoRa.png)
Create README.md 2022-01-30 03:13:02 +00:00			`# Gateway 2.000`

Update README.md 2022-02-06 13:05:35 +00:00			`This is the FDRS Multiprotocol Gateway sketch. The device listens for packets over ESP-NOW, UART, LoRa, and/or MQTT, then retransmits the packets over these interfaces using rules defined in the configuration file.`
Create README.md 2022-01-30 03:13:02 +00:00
Update README.md 2022-02-04 16:22:09 +00:00			`The most commonly used configuration tells the device to take any ESP-NOW packet it receives and output the data over the serial port (UART):`
Create README.md 2022-01-30 03:13:02 +00:00			```
Update README.md 2022-02-03 21:25:08 +00:00			`#define UNIT_MAC 0x00`
Create README.md 2022-01-30 03:13:02 +00:00			`#define ESPNOWG_ACT sendSerial();`
			```
			`The companion for this device, connected via serial, takes any data it receives from the serial port and sends it via MQTT:`
			```
			`#define USE_WIFI`
			`#define SERIAL_ACT sendMQTT();`
			```
			`Splitting the gateway into two devices allows you to use ESP-NOW and WiFi simultaneously without channel conflicts. You can also connect the first device to a computer with a USB-UART adapter and get the data that way, eliminating WiFi altogether.`

			`If you have sensors that are out of range of your first gateway, you can use a gateway as a repeater. First you will set the ESPNOW1 address to that of your first gateway, then you'll direct general ESP-NOW traffic to the ESPNOW1 interface:`
			```
Update README.md 2022-02-07 18:10:31 +00:00			`#define UNIT_MAC 0x01`
Update README.md 2022-02-07 18:07:59 +00:00			`#define ESPNOWG_ACT sendESPNOW(0x00);`
Create README.md 2022-01-30 03:13:02 +00:00			```
Update README.md 2022-02-22 14:14:02 +00:00			`![Basic](/FDRS_Gateway2000/Basic_Setup.png)`


			`![Basic](/FDRS_Gateway2000/Basic_LoRa_Setup.png)`


			`![Basic](/FDRS_Gateway2000/Advanced_Setup_LoRa.png)`