Archives
/
Ender3V2S1
mirror of https://github.com/mriscoc/Ender3V2S1
2
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

Fix CREALITY_CR4NTxxC10 E3 Free-runs

Browse Source
F4-CRC-TEST
Miguel Risco-Castillo 4 months ago
parent f7297881df
commit ef5d0fd025
7 changed files with 253 additions and 179 deletions
Show Stats Download Patch File Download Diff File

164
Marlin/Configuration.h
Unescape Escape View File

@ -71,7 +71,7 @@
// Choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_CREALITY_V24S1_301F4 // Ender 3S1 v301F4
#define MOTHERBOARD BOARD_CREALITY_V4 // Creality Board v4.2.2
#endif
/**
@ -120,7 +120,7 @@
//#define BLUETOOTH
// Name displayed in the LCD "Ready" message and Info menu
#define CUSTOM_MACHINE_NAME "Ender3S1-F4-TJC"
#define CUSTOM_MACHINE_NAME "Ender3V2-422-MM"
// Printer's unique ID, used by some programs to differentiate between machines.
// Choose your own or use a service like https://www.uuidgenerator.net/version4
@ -517,10 +517,10 @@
* ================================================================
* SPI RTD/Thermocouple Boards
* ================================================================
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-1)
* -5 : MAX31865 with Pt100/Pt1000, 2, 3, or 4-wire (only for sensors 0-2 and bed)
* NOTE: You must uncomment/set the MAX31865_*_OHMS_n defines below.
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-1)
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-1)
* -3 : MAX31855 with Thermocouple, -200°C to +700°C (only for sensors 0-2 and bed)
* -2 : MAX6675 with Thermocouple, 0°C to +700°C (only for sensors 0-2 and bed)
*
* NOTE: Ensure TEMP_n_CS_PIN is set in your pins file for each TEMP_SENSOR_n using an SPI Thermocouple. By default,
* Hardware SPI on the default serial bus is used. If you have also set TEMP_n_SCK_PIN and TEMP_n_MISO_PIN,
@ -640,7 +640,7 @@
#define HEATER_5_MAXTEMP 275
#define HEATER_6_MAXTEMP 275
#define HEATER_7_MAXTEMP 275
#define BED_MAXTEMP 120 // Ender3S1 Configs
#define BED_MAXTEMP 120 // Ender Configs
#define CHAMBER_MAXTEMP 60
/**
@ -684,9 +684,9 @@
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
#define DEFAULT_Kd_LIST { 114.00, 114.00 }
#else
#define DEFAULT_Kp 17.10
#define DEFAULT_Ki 1.39
#define DEFAULT_Kd 52.79
#define DEFAULT_Kp 22.89
#define DEFAULT_Ki 1.87
#define DEFAULT_Kd 70.18
#endif
#else
#define BANG_MAX 255 // Limit hotend current while in bang-bang mode; 255=full current
@ -774,9 +774,9 @@
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
#define DEFAULT_bedKp 54.86
#define DEFAULT_bedKi 10.06
#define DEFAULT_bedKd 199.38
#define DEFAULT_bedKp 462.10
#define DEFAULT_bedKi 85.47
#define DEFAULT_bedKd 624.59
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
#else
@ -896,8 +896,16 @@
//#define COREYX
//#define COREZX
//#define COREZY
//#define MARKFORGED_XY // MarkForged. See https://reprap.org/forum/read.php?152,504042
//
// MarkForged Kinematics
// See https://reprap.org/forum/read.php?152,504042
//
//#define MARKFORGED_XY
//#define MARKFORGED_YX
#if ANY(MARKFORGED_XY, MARKFORGED_YX)
//#define MARKFORGED_INVERSE // Enable for an inverted Markforged kinematics belt path
#endif
// Enable for a belt style printer with endless "Z" motion
//#define BELTPRINTER
@ -1111,12 +1119,12 @@
// @section endstops
// Enable pullup for all endstops to prevent a floating state
//#define ENDSTOPPULLUPS // Board v301 Configs
#define ENDSTOPPULLUPS
#if DISABLED(ENDSTOPPULLUPS)
// Disable ENDSTOPPULLUPS to set pullups individually
//#define ENDSTOPPULLUP_XMIN
//#define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN // Board v301 Configs
//#define ENDSTOPPULLUP_ZMIN
//#define ENDSTOPPULLUP_IMIN
//#define ENDSTOPPULLUP_JMIN
//#define ENDSTOPPULLUP_KMIN
@ -1132,7 +1140,7 @@
//#define ENDSTOPPULLUP_UMAX
//#define ENDSTOPPULLUP_VMAX
//#define ENDSTOPPULLUP_WMAX
#define ENDSTOPPULLUP_ZMIN_PROBE // Board v301 Configs
//#define ENDSTOPPULLUP_ZMIN_PROBE
#endif
// Enable pulldown for all endstops to prevent a floating state
@ -1164,11 +1172,11 @@
* Endstop "Hit" State
* Set to the state (HIGH or LOW) that applies to each endstop.
*/
#define X_MIN_ENDSTOP_HIT_STATE LOW // Board v301 Configs
#define X_MIN_ENDSTOP_HIT_STATE HIGH
#define X_MAX_ENDSTOP_HIT_STATE HIGH
#define Y_MIN_ENDSTOP_HIT_STATE LOW // Board v301 Configs
#define Y_MIN_ENDSTOP_HIT_STATE HIGH
#define Y_MAX_ENDSTOP_HIT_STATE HIGH
#define Z_MIN_ENDSTOP_HIT_STATE HIGH // Board v301 Configs
#define Z_MIN_ENDSTOP_HIT_STATE HIGH
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
#define I_MIN_ENDSTOP_HIT_STATE HIGH
#define I_MAX_ENDSTOP_HIT_STATE HIGH
@ -1230,7 +1238,7 @@
* Override with M92
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 424.9 } // Ender Configs
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } // Ender Configs
#define LIMITED_MAX_STEPS_EDITING
#if ENABLED(LIMITED_MAX_STEPS_EDITING)
@ -1286,9 +1294,9 @@
*/
#define CLASSIC_JERK // Ender Configs
#if ENABLED(CLASSIC_JERK)
#define DEFAULT_XJERK 5.0 // Ender Configs
#define DEFAULT_YJERK 5.0 // Ender Configs
#define DEFAULT_ZJERK 0.3 // Ender Configs
#define DEFAULT_XJERK 8.0 // Ender Configs
#define DEFAULT_YJERK 8.0 // Ender Configs
#define DEFAULT_ZJERK 0.4 // Ender Configs
//#define DEFAULT_IJERK 0.3
//#define DEFAULT_JJERK 0.3
//#define DEFAULT_KJERK 0.3
@ -1343,10 +1351,10 @@
* The probe replaces the Z-MIN endstop and is used for Z homing.
* (Automatically enables USE_PROBE_FOR_Z_HOMING.)
*/
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN // Probe connected to BLTouch port
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
// Force the use of the probe for Z-axis homing
#define USE_PROBE_FOR_Z_HOMING
//#define USE_PROBE_FOR_Z_HOMING // Manual mesh not have a probe
/**
* Z_MIN_PROBE_PIN
@ -1375,7 +1383,7 @@
* Use G29 repeatedly, adjusting the Z height at each point with movement commands
* or (with LCD_BED_LEVELING) the LCD controller.
*/
//#define PROBE_MANUALLY
#define PROBE_MANUALLY // Manual mesh version
/**
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
@ -1403,7 +1411,7 @@
/**
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
#define BLTOUCH // 3D/CR/BLTouch version
//#define BLTOUCH
/**
* MagLev V4 probe by MDD
@ -1441,6 +1449,9 @@
* Uses I2C port, so it requires I2C library markyue/Panda_SoftMasterI2C.
*/
//#define BD_SENSOR
#if ENABLED(BD_SENSOR)
//#define BD_SENSOR_PROBE_NO_STOP // Probe bed without stopping at each probe point
#endif
// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)
//#define SOLENOID_PROBE
@ -1564,7 +1575,7 @@
* | [-] |
* O-- FRONT --+
*/
#define NOZZLE_TO_PROBE_OFFSET { -31.8, -40.5, 0 } // Ender3S1 Configs
#define NOZZLE_TO_PROBE_OFFSET { 0, 0, 0 } // MRiscoC BLTouch offset for support: https://www.thingiverse.com/thing:4605354 (z-offset = -1.80 mm) // Manual mesh use the nozzle as probe
// Enable and set to use a specific tool for probing. Disable to allow any tool.
#define PROBING_TOOL 0
@ -1647,13 +1658,13 @@
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
*/
#define Z_CLEARANCE_DEPLOY_PROBE 5 // (mm) Z Clearance for Deploy/Stow // MRiscoC Increase speed
#define Z_CLEARANCE_BETWEEN_PROBES 5 // (mm) Z Clearance between probe points // MRiscoC Increase probe compatibility
#define Z_CLEARANCE_MULTI_PROBE 5 // (mm) Z Clearance between multiple probes // MRiscoC Increase speed
#define Z_CLEARANCE_DEPLOY_PROBE 10 // (mm) Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 5 // (mm) Z Clearance between probe points
#define Z_CLEARANCE_MULTI_PROBE 5 // (mm) Z Clearance between multiple probes
#define Z_PROBE_ERROR_TOLERANCE 3 // (mm) Tolerance for early trigger (<= -probe.offset.z + ZPET)
//#define Z_AFTER_PROBING 5 // (mm) Z position after probing is done
#define Z_PROBE_LOW_POINT -3 // (mm) Farthest distance below the trigger-point to go before stopping // MRiscoC allows reach lower points
#define Z_PROBE_LOW_POINT -2 // (mm) Farthest distance below the trigger-point to go before stopping
// For M851 provide ranges for adjusting the X, Y, and Z probe offsets
//#define PROBE_OFFSET_XMIN -50 // (mm)
@ -1664,7 +1675,7 @@
//#define PROBE_OFFSET_ZMAX 20 // (mm)
// Enable the M48 repeatability test to test probe accuracy
#define Z_MIN_PROBE_REPEATABILITY_TEST // MRiscoC Enable M48 repeatability test
//#define Z_MIN_PROBE_REPEATABILITY_TEST
// Before deploy/stow pause for user confirmation
//#define PAUSE_BEFORE_DEPLOY_STOW
@ -1684,10 +1695,10 @@
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
//#define WAIT_FOR_HOTEND // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
#endif
#define PROBING_FANS_OFF // Turn fans off when probing // MRiscoC Turn fans off for avoid vibrations and interference
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define PROBING_ESTEPPERS_OFF // Turn all extruder steppers off when probing
//#define PROBING_STEPPERS_OFF // Turn all steppers off (unless needed to hold position) when probing (including extruders)
#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors // MRiscoC Wait for stability
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
// Require minimum nozzle and/or bed temperature for probing
//#define PREHEAT_BEFORE_PROBING
@ -1766,10 +1777,13 @@
*/
//#define Z_IDLE_HEIGHT Z_HOME_POS
//#define Z_CLEARANCE_FOR_HOMING 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... // MRiscoC Crearance over the bed
// Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
//#define Z_CLEARANCE_FOR_HOMING 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... // MRiscoC Crearance over the bed
// You'll need this much clearance above Z_MAX_POS to avoid grinding.
#define Z_AFTER_HOMING 5 // (mm) Height to move to after homing (if Z was homed) // MRiscoC Crearance over the bed
//#define XY_AFTER_HOMING { 10, 10 } // (mm) Move to an XY position after homing (and raising Z)
//#define Z_AFTER_HOMING 5 // (mm) Height to move to after homing (if Z was homed) // MRiscoC Crearance over the bed
//#define EVENT_GCODE_AFTER_HOMING "M300 P440 S200" // Commands to run after G28 (and move to XY_AFTER_HOMING)
// Direction of endstops when homing; 1=MAX, -1=MIN
// :[-1,1]
@ -1801,16 +1815,16 @@
// @section geometry
// The size of the printable area
#define X_BED_SIZE 220 // MRiscoC Max usable bed size
#define Y_BED_SIZE 220 // MRiscoC Max usable bed size
#define X_BED_SIZE 230 // MRiscoC Max usable bed size
#define Y_BED_SIZE 230 // MRiscoC Max usable bed size
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
#define X_MIN_POS -10 // MRiscoC Stock physical limit
#define Y_MIN_POS -8 // MRiscoC Stock physical limit
#define X_MIN_POS 0 // MRiscoC Stock physical limit
#define Y_MIN_POS 0 // MRiscoC Stock physical limit
#define Z_MIN_POS 0
#define X_MAX_POS 230 // MRiscoC Stock physical limit
#define Y_MAX_POS 220 // MRiscoC Stock physical limit
#define Z_MAX_POS 270 // Ender Configs
#define X_MAX_POS 248 // MRiscoC Stock physical limit
#define Y_MAX_POS 231 // MRiscoC Stock physical limit
#define Z_MAX_POS 250 // Ender Configs
//#define I_MIN_POS 0
//#define I_MAX_POS 50
//#define J_MIN_POS 0
@ -1883,9 +1897,9 @@
#define FIL_RUNOUT_ENABLED_DEFAULT false // Enable the sensor on startup. Override with M412 followed by M500.
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
#define FIL_RUNOUT_STATE HIGH // Pin state indicating that filament is NOT present. // Board v301 Configs
//#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. // Board v301 Configs
#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. // Board v301 Configs
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
//#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder.
// This is automatically enabled for MIXING_EXTRUDERs.
@ -1930,7 +1944,7 @@
// After a runout is detected, continue printing this length of filament
// before executing the runout script. Useful for a sensor at the end of
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
#define FILAMENT_RUNOUT_DISTANCE_MM 200 // MRiscoC Customizable by menu
#define FILAMENT_RUNOUT_DISTANCE_MM 25 // MRiscoC Customizable by menu
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
// Enable this option to use an encoder disc that toggles the runout pin
@ -2021,9 +2035,9 @@
*/
//#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR
#define AUTO_BED_LEVELING_BILINEAR // MRiscoC BLTouch auto level
//#define AUTO_BED_LEVELING_BILINEAR
//#define AUTO_BED_LEVELING_UBL
//#define MESH_BED_LEVELING
#define MESH_BED_LEVELING // Manual Mesh
/**
* Commands to execute at the end of G29 probing.
@ -2044,14 +2058,14 @@
*/
#define PREHEAT_BEFORE_LEVELING // MRiscoC Heatting to compensate thermal expansions
#if ENABLED(PREHEAT_BEFORE_LEVELING)
#define LEVELING_NOZZLE_TEMP 0 // (°C) Only applies to E0 at this time // MRiscoC No necessary for BLTouch
#define LEVELING_NOZZLE_TEMP 175 // (°C) Only applies to E0 at this time // Preheat nozzle without oozing
#define LEVELING_BED_TEMP 50
#endif
/**
* Enable detailed logging of G28, G29, M48, etc.
* Turn on with the command 'M111 S32'.
* NOTE: Requires a lot of PROGMEM!
* NOTE: Requires a lot of flash!
*/
//#define DEBUG_LEVELING_FEATURE
@ -2114,10 +2128,10 @@
// Subdivision of the grid by Catmull-Rom method.
// Synthesizes intermediate points to produce a more detailed mesh.
//
//#define ABL_BILINEAR_SUBDIVISION // Original Ender3S1 Configs set this to Enable
//#define ABL_BILINEAR_SUBDIVISION
#if ENABLED(ABL_BILINEAR_SUBDIVISION)
// Number of subdivisions between probe points
#define BILINEAR_SUBDIVISIONS 5 // Ender3S1 Configs
#define BILINEAR_SUBDIVISIONS 3
#endif
#endif
@ -2130,7 +2144,7 @@
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
#define MESH_INSET 38 // Set Mesh bounds as an inset region of the bed // MRiscoC Center mesh
#define MESH_INSET 25 // Set Mesh bounds as an inset region of the bed // MRiscoC Center mesh
#define GRID_MAX_POINTS_X 5 // Don't use more than 15 points per axis, implementation limited. // MRiscoC Customizable by menu
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
@ -2172,7 +2186,7 @@
//=================================== Mesh ==================================
//===========================================================================
#define MESH_INSET 38 // Set Mesh bounds as an inset region of the bed // MRiscoC Center mesh
#define MESH_INSET 25 // Set Mesh bounds as an inset region of the bed // MRiscoC Center mesh
#define GRID_MAX_POINTS_X 5 // Don't use more than 7 points per axis, implementation limited. // MRiscoC Customizable by menu
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
@ -2196,13 +2210,13 @@
#define LCD_BED_TRAMMING // ProUI has a bed tramming menu
#if ENABLED(LCD_BED_TRAMMING)
//#define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets // ProUI use mesh insets for bed tramming
#define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
#define BED_TRAMMING_HEIGHT 0.0 // (mm) Z height of nozzle at tramming points
#define BED_TRAMMING_Z_HOP 5.0 // (mm) Z height of nozzle between tramming points
//#define BED_TRAMMING_INCLUDE_CENTER // Move to the center after the last corner
#define BED_TRAMMING_USE_PROBE // Use a probe if it is available
//#define BED_TRAMMING_USE_PROBE
#if ENABLED(BED_TRAMMING_USE_PROBE)
#define BED_TRAMMING_PROBE_TOLERANCE 0.05 // (mm) // ProUI bed tramming wizard tolerance
#define BED_TRAMMING_PROBE_TOLERANCE 0.1 // (mm)
#define BED_TRAMMING_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
//#define BED_TRAMMING_AUDIO_FEEDBACK
#endif
@ -2251,11 +2265,11 @@
* - Allows Z homing only when XY positions are known and trusted.
* - If stepper drivers sleep, XY homing may be required again before Z homing.
*/
#define Z_SAFE_HOMING // MRiscoC Homing Z at center of bed
//#define Z_SAFE_HOMING
#if ENABLED(Z_SAFE_HOMING)
#define Z_SAFE_HOMING_X_POINT X_CENTER // X point for Z homing
#define Z_SAFE_HOMING_Y_POINT Y_CENTER // Y point for Z homing
#define Z_SAFE_HOMING_X_POINT X_CENTER // (mm) X point for Z homing
#define Z_SAFE_HOMING_Y_POINT Y_CENTER // (mm) Y point for Z homing
//#define Z_SAFE_HOMING_POINT_ABSOLUTE // Ignore home offsets (M206) for Z homing position
#endif
@ -2340,7 +2354,7 @@
*/
#define EEPROM_SETTINGS // Persistent storage with M500 and M501 // Ender Configs
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
#if ENABLED(EEPROM_SETTINGS)
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. // Ender Configs
@ -2415,7 +2429,7 @@
#if ENABLED(NOZZLE_PARK_FEATURE)
// Specify a park position as { X, Y, Z_raise }
#define NOZZLE_PARK_POINT { (X_MAX_POS - 2), (Y_MAX_POS - 2), 20 }
#define NOZZLE_PARK_POINT { (X_BED_SIZE + 10), (Y_MAX_POS - 10), 20 }
#define NOZZLE_PARK_MOVE 0 // Park motion: 0 = XY Move, 1 = X Only, 2 = Y Only, 3 = X before Y, 4 = Y before X
#define NOZZLE_PARK_Z_RAISE_MIN 0 // (mm) Always raise Z by at least this distance // MRiscoC uses Park Z Raise from 0 to avoid backlash issues
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
@ -3022,6 +3036,11 @@
//
//#define BTT_MINI_12864
//
// BEEZ MINI 12864 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
//
//#define BEEZ_MINI_12864
//
// Factory display for Creality CR-10 / CR-7 / Ender-3
// https://www.aliexpress.com/item/32833148327.html
@ -3036,14 +3055,14 @@
//#define ENDER2_STOCKDISPLAY
//
// ANET and Tronxy Graphical Controller
//
// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6
// A clone of the RepRapDiscount full graphics display but with
// different pins/wiring (see pins_ANET_10.h). Enable one of these.
// ANET and Tronxy 128×64 Full Graphics Controller as used on Anet A6
//
//#define ANET_FULL_GRAPHICS_LCD
//#define ANET_FULL_GRAPHICS_LCD_ALT_WIRING
//
// GUCOCO CTC 128×64 Full Graphics Controller as used on GUCOCO CTC A10S
//
//#define CTC_A10S_A13
//
// AZSMZ 12864 LCD with SD
@ -3388,7 +3407,6 @@
//
//#define DWIN_CREALITY_LCD // Creality UI
#define DWIN_LCD_PROUI // Pro UI by MRiscoC
#define TJC_DISPLAY
#define USE_STOCK_DWIN_SET
// Professional firmware features:
@ -3406,7 +3424,7 @@
#if ENABLED(DWIN_LCD_PROUI)
#if PROUI_EX
#if ENABLED(LCD_BED_TRAMMING)
#define HAS_TRAMMING_WIZARD 1
//#define HAS_TRAMMING_WIZARD 1 // Manual mesh not have a probe
#endif
#define HAS_GCODE_PREVIEW 1
#define HAS_TOOLBAR 1

247
Marlin/Configuration_adv.h
Unescape Escape View File

@ -684,7 +684,7 @@
* Multiple extruders can be assigned to the same pin in which case
* the fan will turn on when any selected extruder is above the threshold.
*/
#define E0_AUTO_FAN_PIN FAN1_PIN // Board v301 Configs
#define E0_AUTO_FAN_PIN -1 // Ender3V2 Configs
#define E1_AUTO_FAN_PIN -1
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
@ -1006,13 +1006,13 @@
*
* Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
*/
#define BLTOUCH_HS_MODE true
//#define BLTOUCH_HS_MODE true
#ifdef BLTOUCH_HS_MODE
// The probe Z offset (M851 Z) is the height at which the probe triggers.
// This must be large enough to keep the probe pin off the bed and prevent
// it from snagging on the bed clips.
#define BLTOUCH_HS_EXTRA_CLEARANCE 0 // Extra Z Clearance
#define BLTOUCH_HS_EXTRA_CLEARANCE 7 // Extra Z Clearance
#endif
#endif // BLTOUCH
@ -1124,42 +1124,62 @@
#if ENABLED(FT_MOTION)
#define FTM_DEFAULT_MODE ftMotionMode_DISABLED // Default mode of fixed time control. (Enums in ft_types.h)
#define FTM_DEFAULT_DYNFREQ_MODE dynFreqMode_DISABLED // Default mode of dynamic frequency calculation. (Enums in ft_types.h)
#define FTM_SHAPING_DEFAULT_X_FREQ 37.0f // (Hz) Default peak frequency used by input shapers.
#define FTM_SHAPING_DEFAULT_Y_FREQ 37.0f // (Hz) Default peak frequency used by input shapers.
#define FTM_LINEAR_ADV_DEFAULT_ENA false // Default linear advance enable (true) or disable (false).
#define FTM_LINEAR_ADV_DEFAULT_K 0.0f // Default linear advance gain.
#define FTM_SHAPING_ZETA 0.1f // Zeta used by input shapers.
#define FTM_SHAPING_V_TOL 0.05f // Vibration tolerance used by EI input shapers.
#define FTM_SHAPING_DEFAULT_X_FREQ 37.0f // (Hz) Default peak frequency used by input shapers
#define FTM_SHAPING_DEFAULT_Y_FREQ 37.0f // (Hz) Default peak frequency used by input shapers
#define FTM_LINEAR_ADV_DEFAULT_ENA false // Default linear advance enable (true) or disable (false)
#define FTM_LINEAR_ADV_DEFAULT_K 0.0f // Default linear advance gain
#define FTM_SHAPING_ZETA_X 0.1f // Zeta used by input shapers for X axis
#define FTM_SHAPING_ZETA_Y 0.1f // Zeta used by input shapers for Y axis
#define FTM_SHAPING_V_TOL_X 0.05f // Vibration tolerance used by EI input shapers for X axis
#define FTM_SHAPING_V_TOL_Y 0.05f // Vibration tolerance used by EI input shapers for Y axis
//#define FT_MOTION_MENU // Provide a MarlinUI menu to set M493 parameters
/**
* Advanced configuration
*/
#define FTM_BATCH_SIZE 100 // Batch size for trajectory generation;
#define FTM_WINDOW_SIZE 200 // Window size for trajectory generation.
#define FTM_FS 1000 // (Hz) Frequency for trajectory generation. (1 / FTM_TS)
#define FTM_TS 0.001f // (s) Time step for trajectory generation. (1 / FTM_FS)
#define FTM_STEPPER_FS 20000 // (Hz) Frequency for stepper I/O update.
#define FTM_MIN_TICKS ((STEPPER_TIMER_RATE) / (FTM_STEPPER_FS)) // Minimum stepper ticks between steps.
#define FTM_MIN_SHAPE_FREQ 10 // Minimum shaping frequency.
#define FTM_ZMAX 100 // Maximum delays for shaping functions (even numbers only!).
// Calculate as:
// 1/2 * (FTM_FS / FTM_MIN_SHAPE_FREQ) for ZV.
// (FTM_FS / FTM_MIN_SHAPE_FREQ) for ZVD, MZV.
// 3/2 * (FTM_FS / FTM_MIN_SHAPE_FREQ) for 2HEI.
// 2 * (FTM_FS / FTM_MIN_SHAPE_FREQ) for 3HEI.
#define FTM_STEPS_PER_UNIT_TIME 20 // Interpolated stepper commands per unit time.
// Calculate as (FTM_STEPPER_FS / FTM_FS).
#define FTM_CTS_COMPARE_VAL 10 // Comparison value used in interpolation algorithm.
// Calculate as (FTM_STEPS_PER_UNIT_TIME / 2).
// These values may be configured to adjust duration of loop().
#define FTM_STEPS_PER_LOOP 60 // Number of stepper commands to generate each loop().
#define FTM_POINTS_PER_LOOP 100 // Number of trajectory points to generate each loop().
// This value may be configured to adjust duration to consume the command buffer.
// Try increasing this value if stepper motion is not smooth.
#define FTM_STEPPERCMD_BUFF_SIZE 1000 // Size of the stepper command buffers.
//#define FT_MOTION_MENU // Provide a MarlinUI menu to set M493 parameters.
#define FTM_UNIFIED_BWS // DON'T DISABLE unless you use Ulendo FBS (not implemented)
#if ENABLED(FTM_UNIFIED_BWS)
#define FTM_BW_SIZE 100 // Unified Window and Batch size with a ratio of 2
#else
#define FTM_WINDOW_SIZE 200 // Custom Window size for trajectory generation needed by Ulendo FBS
#define FTM_BATCH_SIZE 100 // Custom Batch size for trajectory generation needed by Ulendo FBS
#endif
#define FTM_FS 1000 // (Hz) Frequency for trajectory generation. (Reciprocal of FTM_TS)
#define FTM_TS 0.001f // (s) Time step for trajectory generation. (Reciprocal of FTM_FS)
// These values may be configured to adjust the duration of loop().
#define FTM_STEPS_PER_LOOP 60 // Number of stepper commands to generate each loop()
#define FTM_POINTS_PER_LOOP 100 // Number of trajectory points to generate each loop()
#if DISABLED(COREXY)
#define FTM_STEPPER_FS 20000 // (Hz) Frequency for stepper I/O update
// Use this to adjust the time required to consume the command buffer.
// Try increasing this value if stepper motion is choppy.
#define FTM_STEPPERCMD_BUFF_SIZE 3000 // Size of the stepper command buffers
// (FTM_STEPS_PER_LOOP * FTM_POINTS_PER_LOOP) is a good start
// If you run out of memory, fall back to 3000 and increase progressively
#else
// CoreXY motion needs a larger buffer size. These values are based on our testing.
#define FTM_STEPPER_FS 30000
#define FTM_STEPPERCMD_BUFF_SIZE 6000
#endif
#define FTM_STEPS_PER_UNIT_TIME (FTM_STEPPER_FS / FTM_FS) // Interpolated stepper commands per unit time
#define FTM_CTS_COMPARE_VAL (FTM_STEPS_PER_UNIT_TIME / 2) // Comparison value used in interpolation algorithm
#define FTM_MIN_TICKS ((STEPPER_TIMER_RATE) / (FTM_STEPPER_FS)) // Minimum stepper ticks between steps
#define FTM_MIN_SHAPE_FREQ 10 // Minimum shaping frequency
#define FTM_RATIO (FTM_FS / FTM_MIN_SHAPE_FREQ) // Factor for use in FTM_ZMAX. DON'T CHANGE.
#define FTM_ZMAX (FTM_RATIO * 2) // Maximum delays for shaping functions (even numbers only!)
// Calculate as:
// ZV : FTM_RATIO / 2
// ZVD, MZV : FTM_RATIO
// 2HEI : FTM_RATIO * 3 / 2
// 3HEI : FTM_RATIO * 2
#endif
/**
@ -1257,7 +1277,7 @@
*/
//#define XY_FREQUENCY_LIMIT 10 // (Hz) Maximum frequency of small zigzag infill moves. Set with M201 F<hertz>.
#ifdef XY_FREQUENCY_LIMIT
#define XY_FREQUENCY_MIN_PERCENT 5 // (percent) Minimum FR percentage to apply. Set with M201 G<min%>.
#define XY_FREQUENCY_MIN_PERCENT 5 // (%) Minimum FR percentage to apply. Set with M201 G<min%>.
#endif
//
@ -1325,7 +1345,7 @@
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
// Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
//#define CALIBRATION_REPORTING
// The true location and dimension the cube/bolt/washer on the bed.
@ -1475,11 +1495,6 @@
#define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
#endif
//
// LCD Backlight Timeout
//
#define LCD_BACKLIGHT_TIMEOUT_MINS 5 // (minutes) Timeout before turning off the backlight
#if HAS_BED_PROBE && ANY(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
//#define PROBE_OFFSET_WIZARD // Add a Probe Z Offset calibration option to the LCD menu
#if ENABLED(PROBE_OFFSET_WIZARD)
@ -1583,6 +1598,10 @@
#define SOUND_MENU_ITEM // Add a mute option to the LCD menu // MRiscoC Enable Sound Menu Item
#define SOUND_ON_DEFAULT // Buzzer/speaker default enabled state
#if HAS_WIRED_LCD
//#define DOUBLE_LCD_FRAMERATE // Not recommended for slow boards.
#endif
// The timeout to return to the status screen from sub-menus
//#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
@ -1629,6 +1648,15 @@
#endif // HAS_DISPLAY
#if HAS_FEEDRATE_EDIT
#define SPEED_EDIT_MIN 10 // (%) Feedrate percentage edit range minimum
#define SPEED_EDIT_MAX 999 // (%) Feedrate percentage edit range maximum
#endif
#if HAS_FLOW_EDIT
#define FLOW_EDIT_MIN 10 // (%) Flow percentage edit range minimum
#define FLOW_EDIT_MAX 999 // (%) Flow percentage edit range maximum
#endif
// Add 'M73' to set print job progress, overrides Marlin's built-in estimate
#define SET_PROGRESS_MANUALLY // MRiscoC, Allows display feedback of host printing through GCode M73
#if ENABLED(SET_PROGRESS_MANUALLY)
@ -1768,7 +1796,7 @@
// SD Card Sorting options
#if ENABLED(SDCARD_SORT_ALPHA)
#define SDSORT_REVERSE false // Default to sorting file names in reverse order.
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. // MRiscoC Increase number of sorted items
#define SDSORT_LIMIT 50 // Maximum number of sorted items (10-256). Costs 27 bytes each. // MRiscoC Increase number of sorted items
#define SDSORT_FOLDERS -1 // -1=above 0=none 1=below
#define SDSORT_GCODE true // Enable G-code M34 to set sorting behaviors: M34 S<-1|0|1> F<-1|0|1> // MRiscoC Allows disable file sort by M34 g-code
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. // Ender Configs
@ -1872,7 +1900,7 @@
//#define CONFIGURATION_EMBEDDING
// Add an optimized binary file transfer mode, initiated with 'M28 B1'
//#define BINARY_FILE_TRANSFER // MRiscoC Enabled for easy firmware upgrade
#define BINARY_FILE_TRANSFER // MRiscoC Enabled for easy firmware upgrade
#if ENABLED(BINARY_FILE_TRANSFER)
// Include extra facilities (e.g., 'M20 F') supporting firmware upload via BINARY_FILE_TRANSFER
@ -2197,6 +2225,15 @@
//#define TFT_BTOKMENU_COLOR 0x145F // 00010 100010 11111 Cyan
#endif
//
// LCD Backlight Timeout
// Requires a display with a controllable backlight
//
#define LCD_BACKLIGHT_TIMEOUT_MINS 5 // (minutes) Timeout before turning off the backlight
#if defined(DISPLAY_SLEEP_MINUTES) || defined(LCD_BACKLIGHT_TIMEOUT_MINS)
#define EDITABLE_DISPLAY_TIMEOUT // Edit timeout with M255 S<minutes> and a menu item
#endif
//
// ADC Button Debounce
//
@ -2252,7 +2289,7 @@
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
//#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
@ -2352,10 +2389,10 @@
#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
#define MESH_MIN_X 10
#define MESH_MIN_Y 10
#define MESH_MAX_X 195
#define MESH_MAX_Y 175
#define MESH_MIN_X MESH_INSET
#define MESH_MIN_Y MESH_INSET
#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
#endif
#if ALL(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
@ -2366,7 +2403,7 @@
* Repeatedly attempt G29 leveling until it succeeds.
* Stop after G29_MAX_RETRIES attempts.
*/
#define G29_RETRY_AND_RECOVER
//#define G29_RETRY_AND_RECOVER
#if ENABLED(G29_RETRY_AND_RECOVER)
#define G29_MAX_RETRIES 3
#define G29_HALT_ON_FAILURE
@ -2640,10 +2677,12 @@
//#define FULL_REPORT_TO_HOST_FEATURE // Auto-report the machine status like Grbl CNC
#endif
// Bad Serial-connections can miss a received command by sending an 'ok'
// Therefore some clients abort after 30 seconds in a timeout.
// Some other clients start sending commands while receiving a 'wait'.
// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
/**
* Bad Serial-connections can miss a received command by sending an 'ok'
* Therefore some clients abort after 30 seconds in a timeout.
* Some other clients start sending commands while receiving a 'wait'.
* This "wait" is only sent when the buffer is empty. 1 second is a good value here.
*/
//#define NO_TIMEOUTS 1000 // (ms)
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
@ -2656,6 +2695,15 @@
// For serial echo, the number of digits after the decimal point
//#define SERIAL_FLOAT_PRECISION 4
/**
* This feature is EXPERIMENTAL so use with caution and test thoroughly.
* Enable this option to receive data on the serial ports via the onboard DMA
* controller for more stable and reliable high-speed serial communication.
* Only some STM32 MCUs are currently supported.
* Note: This has no effect on emulated USB serial ports.
*/
//#define SERIAL_DMA
/**
* Set the number of proportional font spaces required to fill up a typical character space.
* This can help to better align the output of commands like `G29 O` Mesh Output.
@ -2699,7 +2747,7 @@
#define MIN_AUTORETRACT 0.1 // (mm) Don't convert E moves under this length
#define MAX_AUTORETRACT 10.0 // (mm) Don't convert E moves over this length
#endif
#define RETRACT_LENGTH 1 // (mm) Default retract length (positive value) // MRiscoC Directdrive
#define RETRACT_LENGTH 5 // (mm) Default retract length (positive value) // MRiscoC Bowden
#define RETRACT_LENGTH_SWAP 13 // (mm) Default swap retract length (positive value)
#define RETRACT_FEEDRATE 40 // (mm/s) Default feedrate for retracting // MRiscoC Bowden
#define RETRACT_ZRAISE 0.2 // (mm) Default retract Z-raise // MRiscoC Bowden
@ -2885,6 +2933,7 @@
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. // MRiscoC Enabled load/unload Filament G-codes
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
#define CONFIGURE_FILAMENT_CHANGE // Add M603 G-code and menu items. Requires ~1.3K bytes of flash.
#endif
// @section tmc_smart
@ -3433,9 +3482,8 @@
/**
* TWI/I2C BUS
*
* This feature is an EXPERIMENTAL feature so it shall not be used on production
* machines. Enabling this will allow you to send and receive I2C data from slave
* devices on the bus.
* This feature is EXPERIMENTAL but may be useful for custom I2C peripherals.
* Enable this to send and receive I2C data from slave devices on the bus.
*
* ; Example #1
* ; This macro send the string "Marlin" to the slave device with address 0x63 (99)
@ -3792,38 +3840,6 @@
*/
//#define CNC_COORDINATE_SYSTEMS
// @section reporting
/**
* Auto-report fan speed with M123 S<seconds>
* Requires fans with tachometer pins
*/
//#define AUTO_REPORT_FANS
/**
* Auto-report temperatures with M155 S<seconds>
*/
#define AUTO_REPORT_TEMPERATURES
#if ENABLED(AUTO_REPORT_TEMPERATURES) && TEMP_SENSOR_REDUNDANT
//#define AUTO_REPORT_REDUNDANT // Include the "R" sensor in the auto-report
#endif
/**
* Auto-report position with M154 S<seconds>
*/
//#define AUTO_REPORT_POSITION
#if ENABLED(AUTO_REPORT_POSITION)
//#define AUTO_REPORT_REAL_POSITION // Auto-report the real position
#endif
/**
* Include capabilities in M115 output
*/
#define EXTENDED_CAPABILITIES_REPORT
#if ENABLED(EXTENDED_CAPABILITIES_REPORT)
#define M115_GEOMETRY_REPORT // MRiscoC Enabled
#endif
// @section security
/**
@ -3866,13 +3882,50 @@
// @section reporting
// Extra options for the M114 "Current Position" report
/**
* Extra options for the M114 "Current Position" report
*/
//#define M114_DETAIL // Use 'M114` for details to check planner calculations
//#define M114_REALTIME // Real current position based on forward kinematics
//#define M114_LEGACY // M114 used to synchronize on every call. Enable if needed.
/**
* Auto-report fan speed with M123 S<seconds>
* Requires fans with tachometer pins
*/
//#define AUTO_REPORT_FANS
//#define REPORT_FAN_CHANGE // Report the new fan speed when changed by M106 (and others)
/**
* Auto-report temperatures with M155 S<seconds>
*/
#define AUTO_REPORT_TEMPERATURES
#if ENABLED(AUTO_REPORT_TEMPERATURES) && TEMP_SENSOR_REDUNDANT
//#define AUTO_REPORT_REDUNDANT // Include the "R" sensor in the auto-report
#endif
/**
* Auto-report position with M154 S<seconds>
*/
//#define AUTO_REPORT_POSITION
#if ENABLED(AUTO_REPORT_POSITION)
//#define AUTO_REPORT_REAL_POSITION // Auto-report the real position
#endif
/**
* M115 - Report capabilites. Disable to save ~1150 bytes of flash.
* Some hosts (and serial TFT displays) rely on this feature.
*/
#define CAPABILITIES_REPORT
#if ENABLED(CAPABILITIES_REPORT)
// Include capabilities in M115 output
#define EXTENDED_CAPABILITIES_REPORT
#if ENABLED(EXTENDED_CAPABILITIES_REPORT)
#define M115_GEOMETRY_REPORT // MRiscoC Enabled
#endif
#endif
// @section gcode
/**
@ -3884,7 +3937,9 @@
//#define GCODE_QUOTED_STRINGS // Support for quoted string parameters
#endif
// Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)
/**
* Support for MeatPack G-code compression (https://github.com/scottmudge/OctoPrint-MeatPack)
*/
//#define MEATPACK_ON_SERIAL_PORT_1
//#define MEATPACK_ON_SERIAL_PORT_2
@ -3892,6 +3947,12 @@
//#define REPETIER_GCODE_M360 // Add commands originally from Repetier FW
/**
* Enable M111 debug flags 1=ECHO, 2=INFO, 4=ERRORS (unimplemented).
* Disable to save some flash. Some hosts (Repetier Host) may rely on this feature.
*/
#define DEBUG_FLAGS_GCODE
/**
* Enable this option for a leaner build of Marlin that removes
* workspace offsets to slightly optimize performance.
@ -3919,8 +3980,6 @@
//#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
#endif
// @section gcode
/**
* Startup commands
*

6
Marlin/Version.h
Unescape Escape View File

@ -37,7 +37,7 @@
#if ENABLED(IS_DEMO)
#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " DEMO, NOT FOR PRODUCTION"
#else
#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " Ender3S1-F4-TJC, based on bugfix-2.1.x"
#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " Ender3V2-422-MM, based on bugfix-2.1.x"
#endif
/**
@ -45,7 +45,7 @@
* here we define this default string as the date where the latest release
* version was tagged.
*/
//#define STRING_DISTRIBUTION_DATE "2023-11-24"
//#define STRING_DISTRIBUTION_DATE "2024-01-06"
#define STRING_DISTRIBUTION_DATE __DATE__
#define STRING_DISTRIBUTION_TIME __TIME__
@ -53,7 +53,7 @@
/**
* Defines a generic printer name to be output to the LCD after booting Marlin.
*/
#define MACHINE_NAME "Ender 3S1"
#define MACHINE_NAME "Ender 3V2"
/**
* The SOURCE_CODE_URL is the location where users will find the Marlin Source

2
Marlin/src/core/boards.h
Unescape Escape View File

@ -467,8 +467,6 @@
#define BOARD_FYSETC_CHEETAH_V30 5250 // FYSETC Cheetah V3.0 (STM32F446RC)
#define BOARD_BLACKBEEZMINI_V1 5251 // BlackBeezMini V1 (STM32F401CCU6)
#define BOARD_CREALITY_CR4NTxxC10 5301 // Creality STM32F401RE
//
// ARM Cortex-M7
//

2
Marlin/src/pins/stm32f4/pins_CREALITY_CR4NTxxC10.h
Unescape Escape View File

@ -226,7 +226,7 @@
#define BEEPER_PIN EXP1_01_PIN
#endif
#elif ENABLED(DWIN_CREALITY_LCD)
#elif ANY(HAS_DWIN_E3V2, IS_DWIN_MARLINUI)
// DWIN ENCODER LCD
#define BTN_ENC EXP1_05_PIN

6
ini/stm32f4.ini
Unescape Escape View File

@ -686,7 +686,7 @@ extra_scripts = ${common_stm32.extra_scripts}
extends = stm32_variant
board = genericSTM32F401RC
board_build.variant = MARLIN_CREALITY_STM32F401
build_flags = ${stm32_variant.build_flags} -DMCU_STM32F401RC -DSTM32F4
build_flags = ${stm32_variant.build_flags} -DMCU_STM32F401RC
-DSS_TIMER=4 -DTIMER_SERVO=TIM5
-DENABLE_HWSERIAL3 -DTRANSFER_CLOCK_DIV=8
build_unflags = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC
@ -725,7 +725,7 @@ board_build.variant = MARLIN_CREALITY_STM32F401
board_build.offset = 0x10000
board_upload.offset_address = 0x08010000
board_build.rename = firmware-{date}-{time}.bin
build_flags = ${stm32_variant.build_flags} -DMCU_STM32F401RE -DSTM32F401xE -DSTM32F4
build_flags = ${stm32_variant.build_flags} -DMCU_STM32F401RE -DSTM32F401xE
build_unflags = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC
monitor_speed = 115200
@ -748,7 +748,7 @@ board = marlin_STM32F401RE_freeruns
board_build.offset = 0x10000
board_upload.offset_address = 0x08010000
board_build.rename = firmware-{date}-{time}.bin
build_flags = ${stm32_variant.build_flags} -DSTM32F401xE
build_flags = ${stm32_variant.build_flags} -DMCU_STM32F401RE -DSTM32F401xE
-DSS_TIMER=4 -DTIMER_SERVO=TIM5
-DTRANSFER_CLOCK_DIV=8
build_unflags = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC

5
platformio.ini
Unescape Escape View File

@ -13,7 +13,7 @@
[platformio]
src_dir = Marlin
boards_dir = buildroot/share/PlatformIO/boards
default_envs = STM32F401RC_creality
default_envs = STM32F103RC_creality
include_dir = Marlin
extra_configs =
Marlin/config.ini
@ -21,6 +21,7 @@ extra_configs =
ini/due.ini
ini/esp32.ini
ini/features.ini
ini/hc32.ini
ini/lpc176x.ini
ini/native.ini
ini/samd21.ini
@ -106,11 +107,9 @@ default_src_filter = +<src/*> -<src/config> -<src/tests>
+<src/gcode/control/M111.cpp>
+<src/gcode/control/M120_M121.cpp>
+<src/gcode/control/M999.cpp>
+<src/gcode/control/T.cpp>
+<src/gcode/geometry/G92.cpp>
+<src/gcode/host/M110.cpp>
+<src/gcode/host/M114.cpp>
+<src/gcode/host/M115.cpp>
+<src/gcode/host/M118.cpp>
+<src/gcode/host/M119.cpp>
+<src/gcode/motion/G0_G1.cpp>

Write Preview
Loading…
Cancel
Save